Allen&Heath Mini Multi Out User Manual
M-mmo card option, Mini multi out, Fitting to idr10 and ilive surfaces
iLive M- MMO Option Instructions AP7654 issue 5
The
Mini Multi Out
(MMO) module is one of several plug-
in card options that may be fitted to iLive Port B or the GLD I/O port.
It provides three formats of multi-channel digital output
simultaneously available for recording, personal monitoring and
signal distribution.
ADAT
3x 8-channel optical ADAT output ports for up to 24 track
recording or signal interfacing using the popular ADAT standard.
iDR / Hearbus
2x 8-channel RJ45 ports suitable for connection
to the Allen & Heath iDR Series digital mix processors and output
expanders. Up to two expanders or iDR units may be connected to
transport up to 16 signals. These connections are also compatible
with the Hearbus personal monitoring distribution hub.
Note
Connect to the Hearbus distribution hub. Do not connect
directly to a Hearbus mixer or ‘Extreme Expander’.
iDR Output A and Output B each have two connections, AUDIO and
DR-LINK. DR-LINK provides meter and status data and is only
needed when connecting to the iDR-out (analogue) or iDR-Dout
(AES, Spdif, Toslink) expanders. To connect to an iDR-8 or iDR-4
mix processor or to a Hearbus hub use the AUDIO port only.
Use CAT5 cables up to 250m (825’) long.
Aviom
®
Plug a CAT5 cable into this port to transport 16 signals to
the Aviom personal monitoring system.
Fitting to the iDR-64, 48, 32, 16 and GLD
The M-MMO card option may be fitted to the Port B slot in the iLive
fixed format MixRacks, and the I/O port in the GLD mixer. Make sure
the equipment is switched off. Remove the 2 screws securing the
blank panel over Port B. Slide the M-MMO card into the slot and
press it firmly into the mating connector. Secure the card in place
using the 2 screws.
Fitting to iDR10 and iLive Surfaces
The option card can be fitted into the Port A or Port B slot in the
Remote Audio 2 (RAB2) module. It is usual to fit the option to Port B
as Port A is typically used for the Surface to MixRack audio link.
Systems fitted with the older Remote Audio module can be
upgraded with the new RAB2 module. The option port is not
available on the T or R Series Surfaces.
Make sure the System is switched off. Remove the 2 screws
securing the blank panel over the port slot . Slide the M-ACE card
into the slot and press it firmly into the mating connector. Secure
the card in place using the 2 screws.
M-MMO Card Option
AP7654
Instructions
Part number M-MMO-A
iDR-out
iDR-Dout
DR-LINK (control)
AUDIO (8 channels)
10
0
PAFL
(CHK)
ON
REMOTE AUDIO 2
SYSTEM LOCK
SYNC
IN
SYNC
OUT
AUDIO
CLOCK
Port B
Port A
10
0
PAF
L
(CH
K)
ON
REM
OT
E A
U
DI
O
2
SYST
EM
L
OCK
SY
NC
IN
SY
NC
OU
T
AU
D
IO
CLO
CK
Port B
MI
NI
iDR
AVIOM
TM
1-8
MU
LT
I-O
UT
AV
IO
M
1
6 c
hanne
l
9-16 17-24
ADAT OUT
/HearBus
DR-LINK
AUDIO
A
B
Co
m
pa
tib
le
(HUB)
iDR Expander
MI
NI
iDR
AVIOM
TM
1-8
MUL
TI
-O
UT
AV
IO
M
1
6
channe
l
9-16 17-24
ADAT OUT
/HearBus
DR-LINK
AUDIO
A
B
Co
m
pa
tib
le
(HUB)
iDR Expander
MINI
iD
R
AV
IO
M
TM
1-
8
MULTI-OUT
AVIOM 16 channel
9-
16
17-
24
AD
AT
O
UT
/H
ea
rB
us
DR
-L
IN
K
AU
DIO
AB
Compatible
(H
U
B)
iD
R
E
xpande
r
iDR10
RAB2 module
RAB2 module
Surface
Port B
Port A
Usually fitted to Port B
Port A = Surface to MixRack audio link
MI
NI
iDR
AVIOM
TM
1-8
MU
LT
I-
O
U
T
AV
IO
M
1
6 c
hanne
l
9-16 17-24
ADAT OUT
/HearBus
DR-LINK
AUDIO
A
B
Co
m
pa
tib
le
(HUB)
iDR Expander
A&
H
I/O Port