American Lighting PRIORI Series Xenon - Manual

WARNING: These products may represent a possible shock or fire hazard if improperly installed or attached in any way.
Products should be installed in accordance with the owners manual, current electrical codes and/or the current National
Electric Code (NEC).
Warning: To avoid electric shock, disconnect power prior to installation.
Caution: Injury to persons and damage to the lamp and/or mounting surface may result if the
lamp is pulled from the surface. To reduce the likelihood of such injury or damage, mount
on a surface that is mechanically sound.
1. Pull the lens cover away from the front edge of the fixture gently rotating toward the back of
the fixture. The lens cover will now be open at a 90° angle to the base of the fixture. (Figure 1)
2. Remove the lens cover from housing gently by sliding each end of the lens toward the front of
the unit while holding at 90°, then closing to about 30° and lifting the metal tab up
through the slot in the end cap. (Figure 1, inset)
3. Place fixture in desired location.
4. Set fixture housing aside and start mounting screws at marks leaving a
1 /
4
” space between surface
and screw head.
5. To gain access to wires contained inside the wiring compartment, push the metal “Quick Clips” in
succession with thumb while holding and lifting off the wiring compartment cover. (Figure 2)
6. Locate and remove whichever knockout is most conveniently located to your 120V power supply.
Knockouts are located on the back and the top of the fixture. (Figure 3)
Supply wires connection:
1. Slip fixture housing over mounting screws along keyhole slots where they narrow to hold fixture in
place and allow magnet on front of housing to hold wiring compartment cover up for “hands-free”
wiring.
2. Tighten mounting screws to secure housing in place.
3. Install cable connecter that is appropriate for the supply wire following National Electric Code and
local codes.
4. Install cable following National Electric Code and local building code requirements. AC supply
should be 120V protected by circuit breaker or fuse.
5. Connect line voltage AC supply wire(s) (Black) to the line voltage AC wire(s) (Black) inside the
fixture. Secure the connection using the quick connector provided.
6. Connect the neutral AC supply wire(s) (White) to the neutral AC wire(s) White inside the fixture.
Secure the connection using the quick connector provided.
7. Connect the ground AC supply wire(s) (Green or bare wire) to the ground AC wire(s) (Green) inside
the fixture. Secure the connection using the quick connector provided. If your system has no
ground wire, you should consult a qualified electrician before proceeding with the installation.
Note: Electric shock, overheating, low or no light output and shortened lamp life can result if
proper grounding is not done.
8. Insure that no wires are exposed after making the electrical connections.
9. Arrange the wires inside the fixture so they will fit under the wiring compartment cover.
10. Take wiring compartment cover from magnet’s hold and tilt it so that back edge slides under back
lip of housing. Push wiring compartment cover firmly until it snaps into place, held by the metal
“Quick Clips”. Note: Be sure that the wires are not pinched or damaged by any part of the housing
or the cover.
Install the bulb(s) provided:
Xenon JCDGY8 (043X-20BP). For best results, use the bulb’s plastic sleeve, a
soft cloth or tissue to handle bulb. Line up pins with socket and gently press bulb into
socket until it is seated.
Replace the lens cover:
While holding the lens cover at 90° to the fixture, insert the small metal tab of the
lens cover that corresponds to the non-slotted holding area into place first. Close the 90° angle to about 30° and
align the other small metal tab with the slot on the other end and insert. Gently push the sides of the lens toward the
back of the unit until the lens holding tabs snap into place. Close the cover by rotating the lens 90° until it snaps
tightly to magnetic closure. Do not operate without lens cover in place.
120 Volt PRIORI Series Xenon Under Cabinet Light
Installation Instructions for 043X Hardwire Series using line voltage
ADDITIONAL SAFETY MEASURES:
1. Bulb becomes hot quickly. Only contact switch when turning on or off fixture.
2. Do not touch hot lens, lens holder or enclosure.
3. Do not look directly at lighted bulb.
4. Keep lamp away from flammable materials.
5. Do not operate lamp with missing or damaged lens.
6. Do not operate without end connector cover in place for any molex ports/connectors not in use.
RV0811-KB
lens cover
Figure 1
Figure 2
Wiring compartment cover
Push “Quick Clips” with
thumb to remove cover.
magnet
appx
appx
Guide metal
tab through
slot in the end cap
to remove lens cover.
Figure 3
Conduit connector
Knockouts
End connector
cover
Remove cover to access
wiring compartment.