American Lighting LMS-3 Series - Manual

WARNING: These products may present a possible shock
or fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with
these instructions, current electrical codes and/or the
current National Electric Code (NEC).
IMPORTANT
The following instructions are provided to assure safe
installation and operation of LED Mini Swivel Series.
Please read carefully before connecting or installing this
product.
1. The LED Mini Swivels are a safe low voltage lighting
system that are suitable for indoor locations only.
2. Do not mount or support these fixtures in a manner
that can cut the outer jacket or damage wire insulation.
3. Always make sure power is disconnected from the LED
fixtures before cutting, mounting, attaching terminal
block, attaching end cap or modifying in any way.
4. Do not exceed the maximum capacity of the 350mA DC
power supply used for any series configuration.
BEFORE YOU START
• Always make sure the LED Bullet is disconnected
from the power source before wiring.
• Determine the number of fixtures your application will
require. There are multiple power connection
configurations and accessories that allow many
installation options. See examples prior to installation to
determine the best configuration for each installation.
Remember, in any case, do not exceed the capacity of the
power supply (sold separately) used for any single run:
• 1-16 watts can be powered by each LED-DR16-350
• 1-15 watts can be powered by each LED-DR18-350D
(use only 15 watts load and save 3 watts for dimming)
SPECIFICATIONS
Operation: 350mA DC
Wiring: Series configuration only - do not wire in parallel!
Hole cut-out size: 1-7/8” for LMS and LMV fixtures;
2-3/4” for LMS-3
Mounting: Recessed applications only
Wattages: LMS, LMV = 1.25 watts each;
LMS = 3 watts each
**** FOR HARDWIRE INSTALLATIONS ONLY ****
Use a 350mA power supply as recommended by the factory. Use
of any other power supply will void the warranty.
Make sure the power source is disconnected before making
any connections.
1. Check that the plastic connector at the end of the lead wire for
each fixture is in operable condition. Insert male plastic connec-
tor into an open female port of a power connector (sold
separately). See Figure 1.
2. When powering only one fixture, it is necessary to insert an end
cap, LED-END-350, into any open ports to complete the series
wiring. When powering fixtures such as these in series, every
port of each power connector must be connected to an end
cap, another power connector or a fixture. The whole set will
not light if any port remains empty.
2. To connect to LED-DR16-350 or LED-DR18-350D power
supplies, cut off the plastic connector of the last power
connector in the series and wire to the secondary side of the
driver (marked DC out), matching polarity. Connect solid red
lead from fixture or power connector (positive) to red lead wire
of power supply (positive) . Black/red striped lead wire from
load (negative) goes to Black lead of power supply (negative).
Use an TL-CONBLK2 (sold separately) if desired to connect
wires. See Figures 2 and 3.
3. Connect 120V AC power to the primary side matching polarity
and turn on power (N = Neutral/common and L = Line/hot).
MOUNTING LED MINI SWIVEL SERIES
1. Always make sure power is disconnected before modifying,
mounting or installing a series of LED Mini Swivel Lights.
2. Drill a 1-7/8” hole for LMS and LMV fixtures; or a 2-3/4” hole for
LMS-3 fixtures.
3. Open steel spring clips, feed lead wires through hole, making
sure that the wire are not in contact with sharp objects.
4. Release spring clips into mounting hole such that they don’t
pinch wires.
5. Maximum number of fixtures per series is
dependent upon the power supply.
Use the information at far left to
determine maximum.
LED MINI SWIVEL SERIES
Installation instructions for LMS, LMV and LMS-3 series fixtures
RV-1416
Figure 2
Figure 3
www.americanlighting.com
TL-CONBLK2
Connect red to red; and black to
black.
Figure 1
LED-CON2-350
LED-CON6-350
LED-CON3-350
LED-CON6-350HW
LED-CON3-350
Using multiple LED-CON2-350s
Wiring examples