American Lighting 024 Series - Manual

WARNING: These products may present a possible shock
or fire hazard if improperly installed or attached in any
way. Products should be installed in accordance with
these instructions, current electrical codes and/or the
current National Electric Code (NEC).
IMPORTANT
The following instructions are provided to assure safe
installation and operation of LED Bullets. Please read
carefully before connecting or installing this product.
1. The LED Bullets are a safe low voltage lighting system
that are suitable for indoor locations only.
2. Do not mount or support the LED Bullet in a manner
that can cut the outer jacket or damage wire insulation.
3. Always make sure power is disconnected from the LED
Bullets before cutting, mounting, attaching terminal
block, attaching end cap or modifying in any way.
4. Do not exceed the maximum capacity of the 350mA
DC power supply used for any series configuration.
BEFORE YOU START
CAUTION: Always make sure the LED Bullet is
disconnected from the power source before wiring.
• Determine the number of LED Bullets your application
will require. There are multiple power connection
configurations and accessories that allow many
installation options. See examples prior to installation
to determine the best configuration for each installa-
tion.
Remember, in any case, do not exceed the capacity of the
power supply (sold separately) used for any single run:
• 1–12 Bullets can be powered by each LED-DR16-350
• 3–12 Bullets can be powered by each LED-DR18-350D
(use only 15 watts load and save 3 watts for dimming)
SPECIFICATIONS
Operation: 350mA DC
Wiring: Series configuration only - do not wire in parallel!
Hole cut-out size: 1”
Mounting: Recessed applications only
Wattage: 1.25W per Bullet
**** FOR HARDWIRE INSTALLATIONS ONLY ****
Use a 350mA power supply as recommended by the factory.
Use of any other power supply will void the warranty.
Make sure the power source is disconnected before making
any connections.
1. Check that the plastic connector at the end of the lead wire
for each LED Bullet is in operable condition. Insert male plastic
connector into an open female port of a power connector
(sold separately). See Figure 1.
2. When powering only one Bullet, it is necessary to insert an
end cap, LED-END-350, into any open ports to complete the
series wiring. When powering Bullets, every port of each
power connector must be connected to an end cap, another
power connector or a Bullet. The whole set will not light if any
port remains empty.
2. When using LED-DR16-350 or LED-DR18-350D power
supplies, cut off the plastic connector of the last power
connector in the series and wire to the secondary side of the
driver (marked DC out), matching polarity. Connect solid red
lead from Bullet (positive) to red power supply lead wire
(positive) . Black/red striped Bullet lead wire (negative) goes
to Black supply lead (negative). Use an TL-CONBLK2 (sold
separately) if desired to connect wires. See Figures 2 and 3.
3. Connect 120V AC power to the primary side matching
polarity and turn on power (N = Neutral/common and
L = Line/hot).
MOUNTING LED BULLET (RECESSED ONLY)
1. Always make sure power is disconnected before modifying,
mounting or installing a series of LED Bullets.
2. Drill a 1” hole in mounting surface.
3. Push plastic connector and lead wires through hole. Insert
Bullet into cabinet.
4. Make sure that the wire is not in contact with sharp objects.
5. Maximum number of Bullets per series is dependent upon
the power supply. Use the information at far left to determine
maximum.
6. For best results in situations where Bullets are mounted
continually facing down, affix the fixture with a small amount
of silicone to secure the fixture in place.
LED BULLETS
Installation instructions for 024 Series
RV-1411
Figure 2
Figure 3
www.americanlighting.com
TL-CONBLK2
Connect red to red; and black to
black.
Figure 1
LED-CON2-350
LED-CON6-350
LED-CON3-350
LED-CON6-350HW
LED-CON3-350
LED-CON6-350
Wiring examples