Anchor FIESTA TENT LINER 10 THRU 30 WIDE - Manual

Assembly Instructions
Fiesta® Tent Liner
10’ thru 30’ wide Smooth or Gathered
1.
The liner should be installed after the fiesta frame has been
assembled, minus cross bars. It will be easier to install the peak/
ridge pulleys for the liner AS the fiesta frame is being assembled
and before the legs are installed (see fig.2). The outer top should
be installed before the liner.
4.
3.
2.
Preparation:
Loop the pulley support strap up and over the PTT
peak casting. Attach the pulley to the D-rings at
the bottom and pass the pull rope through the
pulley so that the quick link at the end of the rope
hangs approximately at ground level. Pull the
loose end of the rope to the side of the tent and
drape it over the eave bar of the frame.
Attach Liner Pulleys to Peak and Ridge:
Lap Liner Sections and Install Eyes:
To join liner end and mid sections, overlap the rein-
forcement peak patches, carefully sealing the matching
velcro. Align the holes of the patches and insert the
eye bolt down thru both patches. From underneath
thread the eye nut onto the eye bolt and tighten. Seal
the velcro edges peak to eave.
Hoist Liner Sections to Peak of Frame:
7.
6.
5.
With all liner sections joined and velcroed and the
perimeter edges loose, attach the pull rope quick link
to the eye bolt of each reinforcement patch. Pull the
ropes over the eave bar to hoist the liner to the peaks
of the frame. Tie off each pull rope securely to a
frame upright to hold it in the hoisted position.
Replace Cross Bars and make final adjustments:
Attach the Liner along the Eave Line:
Attach Liner at the (4) Corners:
After hoisting the liner to the peak of the frame,
attach the (4) corners by wrapping the liner cor-
ner straps around the (4) corner castings so that
they are captured under the eave bars. Cinch
the liner straps to draw the corners snuggly into
the corner.
Fiestas under 24 ft wide use the standard
Fiesta wall hooks at the eave line (see 6-A).
Pass the wall hook under the eave bar and hook
to the wall rope as shown.
To replace the cross bars, separate the velcro between liner sections, as needed. Insert the cross-bar and then re-seal the velcro
so that the cross bar simply passes through the liner. If the liner has wrinkles, adjust the tension in the liner corner straps and
eave straps. If corners are too tight, on Fiestas under 24 ft wide, move liner wall hooks toward the nearest corner side of any
stitching between the top fabric and the wall rope to relieve interference. For Fiestas 24 ft and wider, loosen FASTEX buckles as
needed along the eave and slide them closer to the nearest corner and retighten.
Remove Cross-Bars
1
2
3
4
5-A 5-B
6-A 6-B
PULL
ROPE
PULLEY
PULLEY
SUPPORT
STRAP
QUICK
LINK
PULL
ROPE
QUICK
LINK
REINFORCING
PATCH
EYE
BOLT VELCRO
All Liner Sections
velcroed together
Reinforcement
Patches with
eye bolt
Pull Rope
Corner
Casting
Hip
Bar
Close up of liner
strap looped under
the eaves, around
the corner casting
Fiestas 24 ft and wider hook the FASTEX strap
and buckle to the eave bar. Pass the liner strap
over the eave bar, fasten the FASTEX buckle and
cinch the liner toward the eave bar (see 6-B).
Fiesta Wall
Hook
Wall Rope
Pull Rope
(Tied to
Upright)
FASTEX
Buckle
and strap
Strap from
Outer Fabric
FILIN
05-06