Atop Technology SE8502-M12 Quick Start - Manual

Introduction
Thank you for choosing the Atop IP68 Rated 2-Port Serial to Ethernet Serial
Device Server. The SE8502-M12 Series provide industrial grade media conver-
sion between Ethernet and RS-232/RS-422/RS-485. This Guide covers four
product models:
■ SE8502-M12
IP68 Rated 2-Port RS-232/422/485 to Ethernet Serial Device Server
■ SE8502-M12 (DIN-Rail)
IP68 Rated 2-Port RS-232/422/485 to Ethernet Serial Device Server with
DIN-Rail Mounting Kit
■ SE8502-Sis-M12
IP68 Rated 2-Port RS-422/485 to Ethernet Serial Device Server, 2KV Isolation on
serial ports
■ SE8502-Sis-M12 (DIN-Rail)
IP68 Rated 2-Port RS-422/485 to Ethernet Serial Device Server with DIN-Rail
Mounting Kit, 2KV Isolation on serial ports
Package Check List
Inside the package you will find the following items:
■ SE8502-M12 / SE8502-M12 (DIN-Rail) / SE8502-Sis-M12
SE8502-Sis-M12 (DIN-Rail) x 1
■ DIN-Rail Kit (only for SE8502-M12 (DIN-Rail) and SE8502-Sis-M12
(DIN-Rail)) x 1
■ Hardware Installation Guide (Warranty card is included) x 1
■ Product CD (information on the product as well as software) x 1
Note: please contact your sales representative if any of the above mentioned
products are missing upon purchase. User Name
Password admin
null (leave it blank)
IP
Mask
Gateway 10.0.50.100
255.255.0.0
10.0.0.254
LED Indicators
Name
LAN
COM
RUN
LED
Orange
Green
Orange
Green
Red
Green
Status
On
Off
On
Blinking
On
Off
On
Off
On
Off
On
Blinking
Description
Ethernet is connected at 10Mbps
Ethernet is disconnected
Ethernet is connected at 100 Mbps
Data is transmitting on Ethernet
Data is transmitting on COM port (Tx)
Data is not transmitting on COM port (Tx)
Data is transmitting on COM port (Rx)
Data is not transmitting on COM port (Rx)
Device is powered on
Device is not powered on
Firmware is not running
Firmware is running normally
x
Network Setting
Please set the appropriate IP setting for this
device (SE5404, 10.0.20.100).
DHCP (Obtain an IP automatically)
IP address:
Subnet mask:
Gateway:
Host name:
OK Cancel
10 100 50 0
10 254 0 0
255 255 0 0
Hardware Installation
1. Unpack the Serial Server; make sure it has not suffered any visible external
damages.
2. Proceed to do grounding on the device. This step is of extreme importance
since the back of the product has its ground metal side exposed. For grounding
just connect the corresponding grounding cable to the grounding point, make sure
the cable’s end has a solid contact with the grounding metal side.
Software Setup
DHCP (Dynamic IP):
A DHCP server can automatically assign an IP address and other related network
settings when SE8502-M12 acts as a DHCP Client; by default, the DHCP client
function on SE8502-M12 is disabled; you may activate the DHCP client function
by executing our Serial Manager© Utility.
Assign a Static IP address by:
■ Configure by Telnet
■ Make sure the PC is on the same network as SE8502-M12.
■ Telnet to SE8502-M12 using DOS command “Telnet IP_address 23”.
Example: telnet 10.0.50.100 23.
■ SE8502-M12’s network, link mode and COM port settings can be configured
in the telnet window.
■ Configure by Serial Manager© Utility
Use Serial Manager© Utility on Product CD to configure the SE8502-M12. First
click on “Config” then assign a static IP.
■ Configure by Web Browser
■ Make sure the PC is on the same network as SE8502-M12.
■ Open a web browser; enter the IP address of SE8502-M12 in the address
bar. The default user name is admin and default password is null (leave it
blank).
■ SE8502-M12’s network, link mode and COM port settings can be configured on
different web pages.
■ Click on “Save Configuration” to save settings.
■ Click on “Restart” button to initiate the change if necessary.
3. Connect the device to a suitable power source.
4. Connect the device to the Ethernet network or a PC.
5. Always make sure that your PC is on the same network’s subnet as your
SE8502-M12.
6. Connect SE8502-M12’s serial port to a serial device.
7. Proceed then to mount your SE8502-M12 either to a wall or to your DIN rail
(depending on your current environment and choice of model).
ATTENTION:
Please make sure that the device is grounded properly before
proceeding.
Default Network Setting
LAN
IP68 Rated 2-Port Serial Server
SE8502-M12 Series
Hardware Installation Guide
Version 1.0
Updated on October, 2012
89900435G