Auto Meter 1302 - Manual (Page 2)

SIG.
+12V
LAMP
GND
GND
LAMP
OUT
+12V
To ground (-) negative
Light wire - dash lighting
circuit or 12 Volt (+)
Grommet
To +12 V
ignition source
GND
Back of
speedometer
Sine
Wave
2 Wire
Sender
GND
SIG.
+12V
LAMP
GND
GND
LAMP
OUT
+12V
SIG.
+12V
LAMP
GND
GND
LAMP
OUT
+12V
White (SQ)
To ground (-) negative
Light wire - dash lighting
circuit or 12 Volt (+)
Grommet
To +12 V ignition source
7/8-18 thread
Remove cap for cruise
control cable, otherwise
leave cap installed.
Transmission
take-off
GND
Red (+12 V)
Black (GND)
3-Wire Sender
Back of
speedometer
Drive Key
Supplied with .104 sq x .104 sq
GND
SIG.
+12V
LAMP
GND
GND
LAMP
OUT
+12V
FOR SERVICE CONTACT: AUTO METER PRODUCTS Inc. 413 W. Elm St., Sycamore, IL 60178 USA (815)899-0801 or
Email us at [email protected]
2650-1184 7/24/06
12 mONTH LImITEd WARRANTY
Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the
product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty
exceed the original purchase price of the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred
due to the failure of this product. Warranty claims to Auto Meter must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the
original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the instrument seal, improper
use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc. disclaims any liability for consequential damages
due to breach of any written or implied warranty on all products manufactured by Auto Meter.
Wiring
Auto meter Hall-Effect senders (Square Wave)
- Models 5291 (standard 7/8-18 thread) & 5292 (For Plug in Sensor), 3 wire sender, cruise.
most OEm style or Factory Installed, 2 wire senders (Sine Wave) ImpORTANT
When using most OEM/factory
installed (2 wire) senders, you
must calibrate the speedometer
before it will function properly.
WARNING
This speedometer is not recommended
for vehicles with solid core ignition wires
Use 20 AWG stranded or
heavier wire for hook-up
Use 20 AWG stranded or
heavier wire for hook-up
NOTE: This speedometer provides an output (OUT) terminal that can
be used with late model vehicle installations using the existing Vehicle
Speed Sensor (VSS). In these installations, the VSS signal wire should
be connected to the SIG terminal of the speedometer only. The OUT
terminal should then be connected to where the VSS output was
originally wired. This will provide a buffered VSS signal to the PCM/
computer in the vehicle.
To PCM/
Computer
(see Note)
To PCM/
Computer
(see Note in
above section.)
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you need the
product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be added to the
cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
© 2006 Auto Meter Products, Inc.