Auto Meter 4389 - Manual (Page 4)

G.) * SHIFT LIGHT COLOR SET – To adjust the color of the light on your Level 2 or 3 product, press the MODE (+) button until “CoLr” is displayed, then press
ENTER to confirm your choice.
• If this is your first time selecting the color, your factory programmed preset is RED. When you enter “CoLr” from the menu, the display should
indicate “1” and the shift lite should illuminate RED. Use the MODE (+) and ExIT (–) buttons to cycle up and down the color choices. Use the
chart below for your reference.
Display Indicated Shift Light Color
0 White
1 Red
2 Yellow
3 Green
4 Teal
5 Blue
6 Magenta
• Press ENTER to confirm your color choice and return to Menu Mode.
• NOTE: If yellow is chosen as shift light color, progressive early warning light color changes to Magenta, see Progressive Shift Light set for more info.
H.) SHIFT LIGHT BRIGHTNESS SET – To adjust the high and low brightness settings of your Digital Pro Shift System, press the MODE (+) until “L LV”
(Light LeVel) is displayed and press ENTER to confirm your choice.
• “Lo” is displayed. Factory programmed preset is the lowest setting, “1.” To adjust, use the MODE (+) and ExIT (–) buttons. Max brightness setting
for the Low level from the factory is “11.”
NOTE: Low brightness setting cannot be set higher than 4 light levels below the High setting (i.e. if the High brightness setting is changed to “11” the
new default Low level setting will be “7” and cannot be increased until the High setting is increased).
• Press ENTER to confirm your Low (dim) level setting and proceed to your High (bright) level setting.
• “Hi” is displayed. Factory programmed preset is the brightest setting, “15.” To adjust, use the MODE (+) and ExIT (–) buttons. Lowest brightness
setting for the High setting from the factory is “5”.
NOTE: High brightness setting cannot be set lower than 4 light levels above the Low setting (i.e. if the Low setting is “7”, the High setting cannot be
set lower than “11” without first lowering the Low setting.).
• Press ENTER to confirm your High (bright) level setting and return to menu select option.
I.) PROGRESSIVE SHIFT LIGHT SET – The progressive shift light feature of this product enables a color change and blink feature to alert the driver of the
approaching shift point as well as a potential over-rev situation. To adjust this settings of this feature or turn it on or off, press the MODE (+) button until
“PSL” is displayed, then press ENTER to confirm your choice.
• “PSL 1” should now be displayed. This is the early warning point and is indicated by a solid yellow light. To adjust this point, press ENTER. Use the
MODE (+) and ExIT (–) buttons to adjust the percentage of the current shift point set that you would like the progressive early warning color to
activate. The factory programmed preset for this point is 60%. This entry may be set as low as 10% of the current shift point, or as high as 1 below the
PSL 2 setting. Setting this feature to one below PSL 2 disables this feature. Once you have selected the desired value, press ENTER to confirm.
• “PSL 2” will be displayed if you press the MENU button once after “PSL 1” is displayed. This is the shift point approaching warning indicated by a
blinking yellow light. To adjust this point, press ENTER. Use the MODE (+) and ExIT (–) buttons to adjust the percentage of the current shift point set
that you would like the progressive early warning color to activate. The factory programmed preset for this point is 80%. This entry may be set as
low as 1 above PSL 1, or as high as 100%. Setting this feature to 100% disables the blinking yellow light feature of the progressive shift light function.
Once you have selected the desired value, press ENTER to confirm.
• “PSL 3” will be displayed if you press the MODE (+) button twice after “PSL1” is displayed. This is the over-rev warning and is indicated by a blinking
red light. To adjust this point, press ENTER. Use the MODE (+) and ExIT (–) buttons to adjust the percentage of the current shift point set that you
would like the progressive over-rev warning color to activate. The factory programmed preset for this point is 110%. This entry may be set as low as
101% or as high as 150% of the current shift point setting. Once you have selected the desired value, press ENTER to confirm.
• “on” / “oFF” Press the MODE (+) button three times after the display shows “PSL 1” in order to be able to turn on or off the progressive shift light function.
The factory programmed preset for this function is off. Use the EnTER button to toggle this setting on or off, the MODE (+) button to confirm or the
EXIT button to cancel.
• *NOTE: If you have selected yellow as your chosen shift light color, your early warning progressive light color will change to Magenta.
It will default to yellow for all other color options. The over rev feature remains blinking red even if red is selected as the chosen
shift light color.
J.) PEAk Recall – The DPSS features a “peak” recall or memory to recall the highest RPM reached during a particular run. Scroll through the Menu
Mode [MODE (+)] until the display reads “PEAC” then press ENTER. This will display the highest RPM achieved. To clear the peak press MODE (+).
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify
when you need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it.
($10.00 charge will be added to the cost of “RUSH REPAIR.”) If you are sending product back for warranty adjustment, you must include a copy (or original) of your sales receipt from
the place of purchase.
12 MONTH LIMITED WARRANTy
Auto Meter Products, Inc. warrants to the consumer that this product will be free from defects in material and workmanship for a period of twelve (12) months from date of the original purchase. Products that fall within
this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product failed due to defects in material or workman-
ship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of the Auto Meter instruments nor shall Auto Meter
Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter must be transpotation prepaid and accompanied with
dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the
instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc. disclaims any liability for consequential damages due
to breach of any written or implied warranty on all products manufactured by Auto Meter.
FOR SERVICE SEnD TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 (815) 899-0801
For Email: [email protected]
© 2006 Auto Meter Products. Inc. 2650-1128A 9/19/06
The “Super Bezel” is a registered trademark of Auto Meter Products, Inc.