Auto Meter 4744 - Manual (Page 2)

INSTALLATION INSTRUCTIONS
2 1 / 11 16 // ” & 2 5 / 55 8 // ” PYROMETERS
For EGT models requiring purchased probe
Installation
2 1
⁄
11
16
⁄⁄ ” Pyrometer Back View
Red
Yellow
(+)
Good
Ground
Grommet
Firewall
Black
Good
Ground
Red
to switched
12V (+)
positive
1. Disconnect the negative (-) battery cable.
2. The 2 5 ⁄ 55
8
⁄⁄ ” gauges may be mounted in a 2 5 ⁄ 55
8
⁄⁄ ” diameter hole.
The 2 1 ⁄ 11
16
⁄⁄ ” gauges may be mounted in a 2 1 ⁄ 11
16
⁄⁄ ” diameter hole.
The hole may be either a hole in the dash, a gauge panel or
an Auto Meter Gauge Pod. (It is best to connect all wiring to
the gauge before mounting it into the gauge hole.)
3. Install light in back of gauge and connect white wire to dash
lighting circuit or to any 12-volt source. Connect BLACK wire to
good ground. Connect RED gauge wire to switched 12V source.
Connect BLACK gauge wire to common chassis ground.
4. If installing a separately sold probe, crimp No. 8 wire terminals
(supplied with gauge) to ends of probe wiring. Verify that the
crimped terminals are securely attached to the bare wire in order to
ensure proper accuracy. Warning: Do not solder terminal to wire.
Doing so may affect the accuracy.
5. See probe installation instructions supplied with probe for
proper installation.
6. Connect RED (-) wire terminal to threaded stud marked RED (-
). Connect YELLOW (+) wire terminal to threaded stud marked
YELLOW (+). Fasten using split lockwasher and brass
nuts provided.
7. Verify that all wire connections are correct and secure. Secure
gauge in hole with mounting bracket supplied.
8. Reconnect the negative (-) battery cable.
To Dash
12V (+)
Lighting
Yellow Red Yellow Red
+ - + -
(-)
Crimp terminals securely
to the bare wire.
To Probe To Probe
Installation
Lighting
1. The 2 5 ⁄ 55 8 ⁄⁄ ” gauges may be mounted in a 2 5 ⁄ 55 8 ⁄⁄ ” diameter hole. The 2 1 ⁄ 11 16 ⁄⁄ ”
gauges may be mounted in a 2 1 ⁄ 11 16 ⁄⁄ ” diameter hole. The hole may be either
a hole in the dash, a gauge panel or an Auto Meter Gauge Pod. (It is best
to connect all wiring to the gauge before mounting it into the gauge hole.)
2. Follow the diagram below to connect 12 volt lighting. See
PROBE INSTALLATION to install the probe.
*NOTE ON LUNAR SERIES MODELS: Lunar Series has no external
light. Connect wires as shown in illustration. For maximum
electro-luminescent life, Do Not wire lighting to direct 12 volt
source. The lighting power source should be routed through
OEM dash control, or a separate rheostat. This will allow
you to control the light intensity. Also, the white wire MUST
be connected to power and the black wire to a good ground.
Damage to electrical circuit could occur if connected incorrectly.
2 5
⁄
55
8
⁄⁄ ” Pyrometer Back View
YELLO
W(+) RED(-)
Black
Yellow
(+)
Red
(-)
Good
Ground
Wires to Probe
No. 8 Terminals
To Probe
Good
Ground
To Dash
12V (+)
Lighting
Red
to switched
12V (+)
positive
Black
12 MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the
original purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product
failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of
the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter
must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in
duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter
Products, Inc. disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you
need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be
added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
2650-1129A 2/23/06
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (815) 899-0801
Email us at [email protected]
http://www.autometer.com
© 2006 Auto Meter Products, Inc.
The Super Bezel is a registered trademark of Auto Meter Products, Inc.