Auto Meter 2391 - Manual (Page 2)

NOTE: 18-gage wire is required for installation of this consle. Auto
Meter wire kit no. 2214 is recommended and may be purchased
separately at an auto parts store near you.
NOTE: Use Teflon
Sealing Tape or Sealing
Compound on threads.
Water Temperature
12V BATTERY
(+)
(-)
(S)
12V BATTERY (+)
(-)
GROUND
GROUND
GROUND To dash lighting (12V).
Connect lights
to dash lighting
curcuit (12V).
Temperature
Sender
To Coolant
Temperature
Port On Engine
To Good
Engine
GROUND
To Good
Engine
GROUND
Grommet
Placed In
Firewall
Grommet Placed
In Firewall
Grommet
BACK VIEW
Split Lockwasher
Nut
Nut
Steel Mounting Bracket
with Plastic Insulators.
Steel Mounting Bracket
with Plastic Insulators.
1. Drill a 3/8" dia. hole in firewall. Install rubber grommet provided in
firewall to insulate wire where it passes through sheet metal.
2. Drain antifreeze from cooled radiator into a container. Never drain hot
coolant! Save antifreeze to refill radiator after installation. Remove
existing water temperature sender for indicator light and install new
sender. (For computerized vehicles see caution in Preliminary Steps.) If
indicator light is still desired, a second port must be drilled and tapped in
block.
3. Cut three lengths of 18-gage wire. Strip insulation back 1/4" on each
end of wire and attach solder lug terminals to each end.
4. Connect one end of wire with solder lug terminal to negative (-)
terminal post on back of gauge using split lockwasher and nut
1. Drill a 3/8" dia. hole in firewall. Install rubber grommet provided in
firewall to insulate wire where it passes through sheet metal.
2. Cut two lengths of 18-gage wire. Strip insulation back 1/4" on each
end of wire and attach solder lug terminals to each end.
3. Connect one end of wire with solder lug terminal to negative (-)
terminal position on back of gauge using split lockwasher and nut
1. Insert light bulb and socket assembly into back of gauge. Connect red
lighting wire to 12V power source in dash lighting circuit. Connect
black wires to good engine ground, such as body frame bolt.
2. Reconnect negative (-) battery cable. Re-program your clock and
radio if necessary.
provided. Connect opposite end of wire with solder lug terminal to
good engine ground, such as body frame bolt.
5. Connect one end of wire with solder lug terminal to positive (+)
terminal post on back of gauge using split lockwasher and nut
provided. Connect opposite end of wire with solder lug terminal to
ignition switch or accessory terminal on fuse block.
CAUTION: Be careful not to touch ignition wire to negative (-) terminal
on back of gauge or sender will be damaged.
See final procedures to complete installation.
Voltmeter
provided. Connect opposite end of wire to good engine ground, such
as body frame bolt.
4. Connect one end of wire with solder lug terminal to positive (+)
terminal on back of gauge using split lockwasher and nut provided.
Connect opposite end to 12V terminal on ignition switch or any 12V
source.
See final procedures to complete installation.
Final Procedures
3. Wrap a clean rag around fittings on back of oil pressure gauge and
place a pan on floor under them to protect vehicle interior from
potential leaking oil. Start engine and run for 30 seconds. Shut engine
off and check rag for leaks. If none appear, start engine again and
visually check all connections for leaks.
12 MONTH LIMITED WARRANTY
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 (815) 895-8141
The manufacturer warrants to the consumer that this product will be free from defects in materials and workmanship for a period of twelve (12) months from the date of the original purchase.
Products that fail within this 12 month warranty period will be repaired or replaced at the manufacturer's option to the consumer, when determined by the manufacturer that the product failed
because of defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the instrument and the necessary labor done by the manufacturer to affect the
repair or replacement of the instrument. In no event shall this warranty exceed the original purchase price of the instrument, nor shall the manufacturer be responsible for special, incidental
or consequential damages or costs incurred due to failure of this product. Warranty claims to the manufacturer must be transportation prepaid and accompanied with dated proof of purchase.
This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the
meter seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. The manufacturer disclaims any liability for consequential
damages due to breach of any written or implied warranty on all products made by the manufacturer.
For service send your gauge to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is, the year and model of your vehicle, engine size,
etc., and your phone number. If you are sending a gauge back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
Service
Ignition Switch
Terminal Or
Other 12V
Source that is
turned off when
ign. is off.
Split Lockwasher
Ignition Switch Terminal
Or Other 12V Source that is turned off
when ign. is off.
2/20/01 2650-235D © 2001 Auto Meter Products, Inc.