Auto Meter 2352 - Manual

Instr. No. 2650-317B
1-1/2" Mechanical Mini Gauges
MODEL 2351, 2352 & 2396
INSTALLATION
INSTRUCTIONS
by
®
WARNING: Some late model vehicles use electronic sensors in
their pressure and temperature senders for engine control
functions. Before removing the original senders, we recommend
that you contact your automotive dealer to be sure no critical
functions will be disrupted. With pressure gauges, it is beneficial
to add a T-fitting to install your new gauge and to keep the
warning light operational. This allows you to monitor the pressure
and still have a warning light to indicate emergency conditions.
1. Read instructions thoroughly. Please consult a qualified mechanic if you have
not had training on the proper installation of instruments.
2. Consult your vehicle's repair manual to locate:
A) oil pressure port,
B) 12V ignition switch or fuse box , and
C) water temperature port
3. Determine ideal mounting location. Choose a location that will not obstruct
visibility or impair driving movement.
4. Determine the best route for tubing to follow. Choose a path free of hazards
of moving parts or hot engine components.
5. Assemble tools and parts required for installation.
6. Remove gauges from metal panel. Notice their placement to make
reassembly easier.
7. Disconnect negative (-) battery cable.
8. Hold panel in desired mounting location. Use panel as template and mark
holes to be drilled for mounting. ( For mini consoles, use mounting brackets
as templates.)
9. Drill holes with a 9/64" drill bit and attach metal panel with self-tapping
screws provided.
For actual gauge installation, see further instructions inside.
Preliminary Steps
4. Route tubing through small grommet in firewall and cut to
meet mounted panel (leave one foot of extra length before
cutting). Be sure to avoid potential hazard of moving parts
or hot engine components.
5. Secure gauge in mounted panel using non-insulated
mounting bracket.
6. Slide sealing nut and ferrule on this end of tubing and
tighten in the same manner described in Step 4 (use 9/16"
and 3/8" open-ended wrenches).
Oil Pressure, cont.
Final Procedures
(Follow these steps after you've completed the steps for all three gauges-
listed on inside pages.)
1. Insert light bulb and socket assembly into back of each gauge. Connect all red
lighting wires to 12V power source in dash lighting circuit. This allows the gauge
lights to be dimmed with normal dash lighting and only used at night. Connect the
black wires to good engine ground. (Body frame bolt is a good engine ground.)
2. Reconnect negative (-) battery cable.
3. Wrap a clean rag around fittings on back of oil pressure gauge and place a pan
on floor under them to protect vehicle interior from potential oil leaking. Start
engine and run for 30 seconds. Shut engine off and check rag for leaks. If none
appear, start engine again and visually check all connections for leaks.
SERVICE
For service send your gauge to Auto Meter in a well packed shipping carton. Please include a
note explaining what the problem is, the year and model of your vehicle, engine size, etc., and
your phone number. If you are sending a gauge back for Warranty adjustment, you must
include a copy (or original) of your sales receipt from the place of purchase.
12 MONTH LIMITED WARRANTY
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC.
413 W. Elm St.,
Sycamore, IL 60178
(815) 895-8141
Auto Meter Products, Inc. warrants to the consumer that all Auto gage instruments will be free from defects in materials
and workmanship for a period of twelve (12) months from the date of the original purchase. Products that fail within this 12
month warranty period will be repaired or replaced at Auto Meter's option to the consumer, when determined by Auto
Meter Products, Inc. that the product failed because of defects in material or workmanship. This warranty is limited to the
repair or replacement of parts in the Auto gage instrument and the necessary labor done by Auto Meter Products, Inc. to
affect the repair or replacement of the Auto gage instrument. In no event shall this warranty exceed the original purchase
price of the Auto gage instrument, nor shall Auto Meter Products, Inc. be responsible for special, incidental or
consequential damages or costs incurred due to failure of this product. Warranty claims to Auto Meter Products, Inc. must
be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original
purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month
warranty period. Breaking the meter seal, improper use or installation, accident, water damage, abuse, unauthorized
repairs or alterations voids this warranty. Auto Meter Products, Inc. disclaims any liability for consequential damages due
to breach of any written or implied warranty on all products made by Auto Meter.
®
IMPORTANT
WEAR
SAFETY GLASSES