Auto Meter 6363 - Manual (Page 2)

power-Up
12 MONTH LIMITeD WARRANTY
Auto Meter Products, Inc. warrants to the consumer that all Auto Meter High Performance products will be free from defects in material and workmanship for a period of twelve (12) months from date of the
original purchase. Products that fail within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product
failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of
the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter
must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in
duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter
Products, Inc. disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
SeRVICe
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please specify when you
need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after receiving it. ($10.00 charge will be
added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
FOR SERVICE SEND TO: AUTO MeTeR pRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 USA (815) 899-0801
Email us at [email protected]
http://www.autometer.com
2650-1241-00 5/17/07 © 2007 Auto Meter Products, Inc.
The Super Bezel is a registered trademark of Auto Meter Products, Inc.
12V BATTeRY
NOTe: Some late model vehicles use electronic sensors in their
pressure and temperature senders for engine control
functions. Before removing the original sender, we
recommend that you contact your automotive dealer to be
sure no critical functions will be disrupted.
1. Check that you have all parts required for installation,
and the engine is cool.
2. Disconnect the negative (-) battery cable.
3. Gauge mounts in a 2-
1 /
16
" hole. Use supplied brackets and
nuts to secure gauge to dash.
4 Connect the white wire to dash lighting or switchable 12v light
source, the red wire to switched +12V source and the black wire to
ground.(see diagram for details) Digital display will dim when power
is applied to white wire.
5. Install sender into pressure port of appropriate type. If unit is
to be installed on a high vibration application such as a full
race engine or engine capable of high RpM, it is strongly
recommended that the sender be remote mounted to either
the fenderwell or firewall, to insulate from vibration. Failure to
remote-locate pressure senders on such an application could
result in gauge failure and potential damage to vehicle and/or
operator injury. Braided stainless steel lines are sold separately by
Auto Meter, and can be used to accomplish this. Sender features
1 ⁄
8
" NPT male fitting and comes with ¼" NPT adapter. Sender
should automatically be grounded when installed into a grounded
component.
If not, or if remote relocation of sender is required, a ground
connection to sender “body” may need to be made. (but not to
sender terminal)
6. Route the violet wire through the firewall. If a new hole is drilled in
the firewall, a gromet is recomended. Connect the violet wire to the
terminal post on the pressure sender.
7. Reconnect negative (-) battery cable.
NOTe: Test all fittings and connections for leaks. If any leaks are
detected, Determine the cause of the leak and repair.
Do not operate vehicle if any leaks are detected.
NOTe: Do not remove factory temp sender to install temp sender. If no
location found, a hose adapter can be used.
Caution: LUBRIPLATE ® DS-ES is a non-hazardous substance.
However, it is recommended to wash hands thoroughly after use.
Use teflon sealing compound sparingly
where symbol indicates. (Tape not
recommended on these threads.)
CAUTION!
As a safety precaution, the +12V
terminal of this product should be
fused before connecting to the 12V
ignition switch. We recommend
using a 1 Amp, 3AG fast-acting type
cartridge fuse (Littlefuse ® # 312 001
or an equivalent).
GOOD
ENGINE
GROUND
GROMMET
+ 12V
CONNECTION
RED
BLACK
PRESSURE
SENDER
FUSE
(SEE CAUTION LEFT)
FIREWALL
OPTIONAL SLIT TUBING RECOMMENDED
(AVAILABLE AT MOST HARDWARE STORES)
WHITE
+12V
DASH
Installation - Oil pressure
VIOLET
When power is applied to the gauge, the display will light up with all eights immediately followed by the gauge firmware version. After the
firmware version is momentarily displayed, the gauge will begin normal operation and display real time sender readings.
Sender error
If no sender is connected, the gauge will display “EØ”. Approximately 4 seconds after the sender is connected, the gauge will display the
fuel level and resume normal operation. If sender is hooked up and “EØ” is displayed, check sender for improper ground or open circuit.