Auto Meter 5690 - Manual (Page 3)

• To display the Peak RPM, press and release the ‘-’ (left) button. The pointer will move to the Peak RPM captured for 4 seconds. The Backlight will change to
the state of the captured RPM (i.e. if Over-Rev Point RPM is set to 8,000 rpm, and the captured peak is 8,300 rpm, the Backlight will begin flashing the Over-
Rev color).
- Peak Recall, Over-Rev Point and Backlight Color:
Programming Mode 4
NOTE: Peak RPM values will only be recorded after the RPM has bee above 3000 RPM for 3 seconds.
NOTE: Over-Rev Point RPM cannot be set below Shift Point RPM.
• To clear the recall Peak RPM, press and release the ENTER (middle) button while the Peak RPM is being shown. The tach will return to normal mode.
• To view the Over-Rev Point RPM, press the ‘+’ (right) button while the Peak RPM is being shown. The pointer will move to Over-Rev Point RPM, with the
backlight displaying the Over-Rev color, for 4 seconds. After 4 seconds of no button presses, the tach will return to normal mode.
• To Edit Over-Rev Point RPM, while the pointer and Backlight are displaying the Over-Rev set point and color:
• Use the ‘+’ (right) button to increase the pointer position and the ‘-’ (left) button to decrease the pointer position until the pointer indicates the desired RPM. If
there are no button presses for four seconds, the tach will return to normal tach mode
without saving the RPM change.
• Press and release the ENTER (middle) button to capture and save the new Over-Rev RPM. The Backlight will begin flashing twice per second. If the there are
no button presses for four seconds, the tach will return to normal tach mode,
saving the Over-Rev RPM point.
• While the Backlight is flashing, use the ‘+’ (right) button and or the ‘-’ (left) button to advance through the seven color choices for the Over-Rev back light. If
there are no button presses for four seconds, the tach will return to normal tach mode
without saving any changes to the Backlight color.
• With the desired Over-Rev Backlight color active, press and release the ENTER (middle) button to save the Over-Rev Backlight color.
• To display Shift Point RPM, press and release the ENTER (middle) button. The pointer will display current Shift Point RPM, with the backlight displaying the
Shift Point color, for 4 seconds.
• To Edit Shift Point RPM, while the pointer and Backlight are displaying the Shift Point set point and color:
- Shift Point RPM and Backlight Color:
Programming Mode 3
NOTE: Shift Point RPM can not be set below Warning Point RPM, or above Over-Rev Point RPM.
• Use the ‘+’ (right) button to increase the pointer position and the ‘-’ (left) button to decrease the pointer position until the pointer indicates the desired RPM. If
there are no button presses for four seconds, the tach will return to normal tach mode
without saving the RPM change.
• Press and release the ENTER (middle) button to capture and save the new Shift Point RPM. The Backlight will begin flashing twice per second. If the there
are no button presses for four seconds, the tach will return to normal tach mode,
saving the Shift Point RPM point.
• While the back light is flashing, use the ‘+’ (right) button and or the ‘-’ (left) button to advance through the seven color choices for the Shift Point Backlight. If
there are no button presses for four seconds, the tach will return to normal tach mode
without saving any changes to the Backlight color.
• With the desired Shift Point back light color active, press and release the ENTER (middle) button to save the Shift Point Backlight color and RPM.
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. If you are sending product
back for warranty adjustment, you must include a copy (or original) of your sales receipt from the place of purchase.
12 MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that this product will be free from defects in material and workmanship for a period of twelve (12) months from date of the original
purchase. Products that fall within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that
the product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed
the original purchase price of the Auto Meter instruments nor shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the
failure of this product. Warranty claims to Auto Meter must be transportation prepaid and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of
product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty period. Breaking the instrument seal, improper use or installation, accident,
water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc. disclaims any liability for consequential damages due to breach of any written or
implied warranty on all products manufactured by Auto Meter.
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 (866) 248-6357
Email: [email protected]
© 2009 Auto Meter Products. Inc. 2650-1417-00rB 6/3/09 The “Super Bezel” is a registered trademark of Auto Meter Products, Inc.