Auto Meter 3890 - Manual (Page 2)

FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 (815) 899-0801
For Email: [email protected]
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please
specify when you need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after
receiving it. ($10.00 charge will be added to the cost of “RUSH REPAIR.”) If you are sending product back for Warranty adjustment, you must include a copy (or original) of
your sales receipt from the place of purchase.
12 MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that this product will be free from defects in material and workmanship for a period of twelve (12) months from date of the original purchase. Products that fail
within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product failed due to defects in material or
workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of the Auto Meter instruments nor shall
Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter must be transportation prepaid and
accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month warranty
period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc. disclaims any liability for
consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
2650-1166 7/10/06 © 2006 Auto Meter Products, Inc.
1.1 To enter this mode, apply power to the tach by turning the ignition switch to the “Accessory” or “On” position. Do not start the engine!
Press and release both the LEFT “+” and RIGHT “-” buttons at the same time. The pointer will indicate the current Shift-Lite set point.
1.2 Using the RIGHT “-” and LEFT “+” buttons, move the pointer to the desired RPM for the new Shift-Lite Set Point. Pressing the LEFT
button will cause the pointer to move up (CW), pressing the RIGHT “-” button will cause the pointer to move down (CCW).
1.3 Press and release both the LEFT “+” and RIGHT “-” buttons at the same time to save the setting and exit Shift-Lite Set Mode.
Operation
1 Shift-Lite Set Mode
WHITE
FUSE
RED
12V DASH LIGHTING
12V IGNITION SWITCH (+)
BLACK BLACK
GREEN
GREEN GREEN OR
GROMMET IN
FIREWALL
EARLY MODEL IGNITION
GOOD ENGINE GROUND
TACH
TERMINAL
ELECTRONIC IGNITION
CAUTION!
As a safety precaution the Red wire of this product should be fused before connecting it to the
positive (+) side of the 12V DC battery. We recommend using a 4 Amp, 3AG fast-acting type
cartridge fuse (Littlefuse® # 312 004 or an equivalent) inline with the Red wire of our product.
• Shift-Lite connector must be plugged in prior to operation.
(SEE CAUTION BELOW)
WARNING
Warranty will be void if connected
to coil when using an aftermarket
ignition box such as, but not limited
to products from the following
manufacturers: MSD, Crane, Jacobs,
Mallory, Holley, Etc.. Prior to
installation of your tachometer, check
with the ignition box manufacturer
for recommended tachometer signal
location.
* See autometer.com/tech_installation.aspx for specific vehicle information.
*