Auto Meter 880246 - Manual (Page 2)

Mounting
1. Mount a 3 1 /
8
" tachometer in a 3 5 /
32
" dia. hole, a 3 3 /
8
" tachometer in a 3 3 /
8
" dia. hole and a 5" tachometer
in a 4 5 /
8
" dia. hole. Be careful not to cut the hole too large.
2. Cut a 3 /
8
" dia. hole in the firewall for the tachometer wires. Place a rubber grommet in the hole and route
the wires through the grommet to the engine compartment.
3. Connect the tachometer wires as shown in the wiring sections.
4. Secure the tachometer to the dashboard using the provided bracket and hardware.
SERVICE
For service send your product to Auto Meter in a well packed shipping carton. Please include a note explaining what the problem is along with your phone number. Please
specify when you need the product back. If you need it back immediately mark the outside of the box “RUSH REPAIR,” and Auto Meter will service product within two days after
receiving it. ($10.00 charge will be added to the cost of “RUSH REPAIR.”) If you are sending product back for warranty adjustment, you must include a copy (or original) of your
sales receipt from the place of purchase.
12 MONTH LIMITED WARRANTY
Auto Meter Products, Inc. warrants to the consumer that this product will be free from defects in material and workmanship for a period of twelve (12) months from date of the original purchase. Products that
fall within this 12 month warranty period will be repaired or replaced at Auto Meter’s option to the consumer, when it is determined by Auto Meter Products, Inc. that the product failed due to defects in material
or workmanship. This warranty is limited to the repair or replacement of parts in the Auto Meter instruments. In no event shall this warranty exceed the original purchase price of the Auto Meter instruments nor
shall Auto Meter Products, Inc. be responsible for special, incidental or consequential damages or costs incurred due to the failure of this product. Warranty claims to Auto Meter must be transpotation prepaid
and accompanied with dated proof of purchase. This warranty applies only to the original purchaser of product and is non-transferable. All implied warranties shall be limited in duration to the said 12 month
warranty period. Breaking the instrument seal, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids this warranty. Auto Meter Products, Inc. disclaims any liability
for consequential damages due to breach of any written or implied warranty on all products manufactured by Auto Meter.
CAUTION!!!
As a safety precaution, the 12V terminal of this
product should be fused before connecting it
to the 12V ignition switch. We recommend
using a 1 Amp, 3AG fast-acting type cartridge
fuse (Littlefuse
® #312 001 or an equivalent).
WARNING
Warranty will be void if connected to coil when using
an aftermarket ignition box such as, but not limited
to products from the following manufacturers: MSD,
Crane, Jacobs, Mallory, Holley, Etc.. Prior to installation
of your tachometer, check with the ignition box manu-
facturer for recommended tachometer signal location.
3 1 /
8
" Models 3 3 /
8
" Models 5" Models
FOR SERVICE SEND TO: AUTO METER PRODUCTS, INC. 413 W. Elm St., Sycamore, IL 60178 (815) 899-0801
For Email: [email protected]
© 2006 Auto Meter Products. Inc. 2650-1138 5/10/06
The “Super Bezel” is a registered trademark of Auto Meter Products, Inc.
12V BATTERY
COIL
- OR -
+
_
Wiring
2¼" 2 1 / 8 "
3 9 / 64 "
3 5 / 16 "
3¾" 3 11 / 32 "
2 3 / 8 "
4 15 / 16 " 4 19 / 32 "
FUSE
GROMMET
IN FIREWALL
LIGHT WIRE -
DASH
LIGHTING
CIRCUIT OR
12VOLT (+)
EARLY
MODEL
IGNITION
ELECTRONIC
IGNIITION
TACH
TERMINAL
12V IGNITION
SWITCH