BELLA 14152 Electric Kettle - Manual (Page 7)

5
Before Using for the First Time
1. Boil a kettle of water following the Operating Instructions described in this Instruction Manual.
2. Discard the boiled water. Your kettle is now ready for use.
Operating Instructions
CAUTION: Do not immerse power base, power cord, or plug in water or any other liquid.
1. Position the power base on a stable, level surface near an electrical outlet. Unwind the power cord from
the cord storage area located beneath the power base. Make sure the cord exits through the cord exit slot
on the side of the power base.
2. Check that the ON/OFF switch is in the OFF (up) position.
3. Remove the kettle from the power base. Remove the lid. Fill with fresh, cold water to the desired level.
The kettle yields up to 5 cups (1.2 liters) of water. Add water but do not fill above the MAX water level.
Wipe excess water off the kettle.
CAUTION: Never add water above the MAX water level. This could cause boiling water to splatter out.
NOTE: If the kettle is accidentally switched ON without sufficient water, a boil-dry protection device will
automatically turn the unit OFF. (See Boil-Dry Protection explanation in this Instruction Manual.)
4. Check to be sure the sealing ring is properly assembled onto the lid. Close the lid and press down gently
until it snaps into position to ensure it is fully closed. Otherwise the kettle may not turn OFF after boiling.
CAUTION: To avoid the risk of splashing while pouring hot water, make sure the lid is securely closed onto
the kettle before operation.
5. Place the kettle on the power base, taking care not to spill any water.
6. Plug the power cord into a 120V AC electrical outlet. Press the ON/OFF switch down to the ON position.
The lighted button will illuminate. Water will begin heating immediately.
7. When a rolling boil is reached, the lighted button will then turn off; the ON/OFF switch will lift (up)
automatically and the kettle will turn OFF.
NOTE: The kettle can be turned OFF any time during the heating process by lifting the ON/OFF switch up.
WARNING: This appliance generates heat and escaping steam during use. Proper precautions must be
taken to prevent the risk of burns, fires, or other injury to persons or damage to property. Keep hands
and face clear of the area above the kettle.
8. Grasp the handle and carefully lift the kettle from the power base before pouring.
CAUTION:
Always check that the ON/OFF switch is in the OFF (up) position before removing it from
the power base.
CAUTION: To avoid a risk of splashing, make sure the lid is securely closed onto the kettle before
operating. Pour slowly and be careful not over-tilt the kettle.
CAUTION: Do not touch hot surfaces!
9. To reheat, check the water level to ensure it is above the MIN water level. If necessary, add more water
before returning the kettle to the power base.
10. Allow at least 30 seconds before pressing the ON/OFF switch down to the ON position.
11. When not in use unplug the power cord from the wall outlet. Allow the unit to cool completely before
cleaning. Empty the kettle after each use. Do not allow water to sit in the kettle overnight. See User
Maintenance Instructions.
Boil-Dry Protection
A safety thermostat will automatically turn the kettle OFF whenever the unit is without sufficient water, or if the
kettle is allowed to boil dry. To reset the boil-dry protection device, remove the kettle from the power base and
allow it to cool before refilling with water.
User Maintenance Instructions
This appliance requires little maintenance. It contains no user serviceable parts. Do not try to repair it
yourself. Any servicing requiring disassembly must be performed by a qualified appliance repair technician.
Care & Cleaning Instructions
CAUTION: Always unplug kettle and allow to cool before cleaning. Never immerse kettle, power base, cord,
or plug in water or other liquids. Never use scouring pads or harsh cleansers to clean your kettle as they may
damage the surface.
1. Make sure the kettle is unplugged and completely cool.
2. Grasp the handle and remove the kettle from the power base. If necessary, wipe the inside and outside
of the kettle with a soft, damp cloth and wipe dry.
3. Wipe the power base with a damp cloth.
4. Make sure both the power base and kettle are completely dry after cleaning and before use.