Blue Sea Systems 7601 m-Series Automatic Charging Relay - 12/24V DC 65A - Manual (Page 2)

start
run accessory
off
Dual Circuit Plus™ Battery Switch 6011
Included in Mini Add-A-Battery kit,
recommended for 7601 m -ACR
m -ACR 7601
COMMON BUS BAR
GROUND
START KEY SWITCH
Engines with
combined alternator
and starter wires
- typical of outboard motors
2 1
House Start
10A FUSE
16 AWG 16 AWG
OPTIONAL
START ISOLATION
(SI) WIRE
2A FUSE
OPTIONAL SWITCH
FOR NO CURRENT DRAW
WHEN IN STORAGE
Outboard
Accessories
FRONT
BACK - NO COVER SIDE - NO COVER
2.85"
72.3mm
2.18"
55.2mm
SIDE - WITH COVER
0.38"
9.7mm
0.13"
3.2mm
0.39"
10mm
0.44"
11.1mm
STUD
HEIGHT
0.84"
21.4mm
1.02"
25.8mm
1/4"-20
FRONT PANEL
MOUNT IN
Ø2-5/8" (67mm)
HOLE WITH
MAX. PANEL
THICKNESS
5/16" (8mm)
REAR PANEL
MOUNT IN
Ø2-5/16"
59mm
HOLE
1.84"
46.7mm
2.57"
65.2mm
1.22"
30.9mm
Ø 2.06"
52.2mm
2.85"
72.3mm
2.825"
71.76mm
2.176"
55.27mm
2.825"
71.76mm
2.176"
55.27mm
0.153"
3.87mm
0.310"
7.87mm
1.298"
32.97mm
1.770"
44.96mm
3.068"
77.94mm
0.753"
19.11mm
0.900"
22.86mm
REAR PANEL
MOUNT IN
Ø2-5/16"
59mm
HOLE
FRONT PANEL
MOUNT IN Ø2-5/8"
67mm HOLE
m
-ACR Installation Diagram
Dimensioned Drawings
Mini Add-A-Battery Installation Diagram
425 Sequoia Drive
Bellingham, WA 98226 USA
p 360.738.8230
p 800.222.7617 USA and Canada
f 360.734.4195
[email protected]
www.bluesea.com
10A
FUSE
16 AWG
COMMON BUS BAR
GROUND
OPTIONAL SWITCH
FOR NO CURRENT DRAW
WHEN IN STORAGE
start
run accessory
off
START KEY SWITCH
OPTIONAL
START ISOLATION
(SI) WIRE
2A
FUSE
Outboard Accessories
Start House
m -ACR 7601
16 AWG
• These installation diagrams show typical applications only. Your application may differ.
For further information, please go to www.bluesea.com and navigate to Resources/Application Briefs
and Technical Briefs.
• Because the m -ACR is dual sensing, the battery connection terminals are interchangeable.
m -ACR function will not be affected by reversal of the starting and house batteries versus the diagram.
• If the status indicator LED is triple-flashing, the m -ACR is in a lockout state, and will not combine
batteries until the lockout condition is removed. Ensure neither battery is below 10V for a 12V system
or 20V for a 24V system.
• If the status indicator LED is double-flashing, check for positive voltage on the start isolation terminal.
• It is recommended that the m -ACR be connected directly to your battery positive terminals through
appropriately sized fuses. Connecting in a different location such as a battery switch may affect
accuracy because of voltage drop along current carrying conductors.
• If you are not knowledgeable about marine electrical systems,
please consult an electrical professional for help with installation.
• If your electrical system is configured with a charging source that cannot supply
the full load current being drawn from the batteries, open/close cycling
can occur. If this cycling continues, the second battery bank
could eventually discharge even though a charge source is present.
See Wire Size and Fuse Rating chart for connections from ACR positive terminals.
Note: To determine wire sizes and fuse ratings for all other wires illustrated, please visit
the Circuit Wizard at circuitwizard.bluesea.com
m -Series, Dual Circuit Plus™ Battery Switch 6011
(Included with 7649 Mini Add-A-Battery)
m ACR, Automatic Charging Relay 7601
Guarantee
Blue Sea Systems stands behind its products for as long as you own them.
Find detailed information at www.bluesea.com/about.
For customer service, call 800-222-7617.