Blue Sea Systems 8244 AC Micro Voltmeter - 0 to 15V AC - Manual

Meter Specifi cations
PN Voltage
Input Voltage: 8244/9353 0-150 Volts AC
8245/9354 0-250 Volts AC
Amperage Draw: 1 Milliampere
Display: Analog
scale
Accuracy: 3% of scale range
PN Inches Millimeters
Face Width: 8244/8245 2 50.80
9353/9354 2-5/8 66.70
Mounting Hole: 8244/8245 1-1/2 38.10
9353/9354
1-7/8 47.60
2. Select mounting location and cut opening
Select a mounting location which is protected from water on the meter front and back and is not
in an area where fl ammable vapors from propane, gasoline or lead acid batteries accumulate.
The meter is not ignition protected and may ignite such vapors. There are two mounting
methods for the meters, surface mount or panel mount.
Surface Mount: Drill fi ve clearance holes as shown below. The part number of the meter will
determine the size and location of the clearance holes. Use the nuts and washers supplied in the
accessory package to secure the four mounting studs to the mounting surface. This method will
work on mounting surfaces up to 5/8” thick.
0-150 Volts PN 8244 / PN 9353
0-250 Volts PN 8245 / PN 9354
Marine Electrical Products
Analog AC Voltmeter
Blue Sea Systems Inc.
425 Sequoia Drive Bellingham, WA 98226 USA
Phone (360) 738-8230 Fax (360) 734-4195
E-mail [email protected]
www.bluesea.com
9332 Rev. 003
Warning
It is not possible within the scope of these
instructions to fully acquaint the installer
with all the knowledge of electrical systems
that may be necessary to correctly install
this product. If the installer is not
knowledgeable in electrical systems we
recommend that an electrical professional
be retained to make the installation.
1. Disconnect all AC and DC power
Disconnect all AC power originating on or
off the vessel. This includes inverters,
generators, shore power attachments and
any other device capable of supplying AC
power to the ship’s circuits. Disconnect the
main positive DC cable from all batteries to
eliminate the possibility of a short circuit
and to disable the inverter while installing
the meter.
Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick
panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use
PN 8013 to mount a single meter or PN 8014 to mount two meters.
(
Installation (continued)
Installation
PN 8244 / PN 8245
Micro Meters
PN 9353 / PN 9354
Standard Meters
Guarantee
Any Blue Sea Systems product with which
a customer is not satisfi ed may be returned
for a refund or replacement at any time.
Meter Specifi cations
PN Voltage
Input Voltage: 8244/9353 0-150 Volts AC
8245/9354 0-250 Volts AC
Amperage Draw: 1 Milliampere
Display: Analog
scale
Accuracy: 3% of scale range
PN Inches Millimeters
Face Width: 8244/8245 2 50.80
9353/9354 2-5/8 66.70
Mounting Hole: 8244/8245 1-1/2 38.10
9353/9354
1-7/8 47.60
2. Select mounting location and cut opening
Select a mounting location which is protected from water on the meter front and back and is not
in an area where fl ammable vapors from propane, gasoline or lead acid batteries accumulate.
The meter is not ignition protected and may ignite such vapors. There are two mounting
methods for the meters, surface mount or panel mount.
Surface Mount: Drill fi ve clearance holes as shown below. The part number of the meter will
determine the size and location of the clearance holes. Use the nuts and washers supplied in the
accessory package to secure the four mounting studs to the mounting surface. This method will
work on mounting surfaces up to 5/8” thick.
0-150 Volts PN 8244 / PN 9353
0-250 Volts PN 8245 / PN 9354
Marine Electrical Products
Analog AC Voltmeter
Blue Sea Systems Inc.
425 Sequoia Drive Bellingham, WA 98226 USA
Phone (360) 738-8230 Fax (360) 734-4195
E-mail [email protected]
www.bluesea.com
9332 Rev. 003
Warning
It is not possible within the scope of these
instructions to fully acquaint the installer
with all the knowledge of electrical systems
that may be necessary to correctly install
this product. If the installer is not
knowledgeable in electrical systems we
recommend that an electrical professional
be retained to make the installation.
1. Disconnect all AC and DC power
Disconnect all AC power originating on or
off the vessel. This includes inverters,
generators, shore power attachments and
any other device capable of supplying AC
power to the ship’s circuits. Disconnect the
main positive DC cable from all batteries to
eliminate the possibility of a short circuit
and to disable the inverter while installing
the meter.
Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick
panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use
PN 8013 to mount a single meter or PN 8014 to mount two meters.
(
Installation (continued)
Installation
PN 8244 / PN 8245
Micro Meters
PN 9353 / PN 9354
Standard Meters
Guarantee
Any Blue Sea Systems product with which
a customer is not satisfi ed may be returned
for a refund or replacement at any time.