Badger Basket 460 - Manual (Page 4)

Custom Built in America. For Today. For the Future.
SPECIFICATIONS
460 Carrier Engine
Cummins ISB-280, turbo-charged, charge-air cooled, 6-cylinder,
4-cycle, liquid-cooled, isolation-mounted diesel engine. 280 peak
hp (209kw) @ 2,300 rpm, 660 lbs.-ft. peak torque (895Nm) @
1,600 rpm, 409 cid (6.7L), 4.21" bore x 4.88 stroke (107mm x
124mm), 17.3:1 compression ratio. Electronically controlled
exhaust gas particulate filter. Two-stage dry-type air cleaner.
Spin-on coolant, fuel/water separator and combination full
flow/bypass lube filters. 12 volt DC, 100 amp alternator with
integral solid-state regulator. Electronically controlled fuel pump.
Battery: One SAE 12 volt DC, 1,150 CCA @ 0 deg. F (-22˚ C)
Radiator: Fin and flat tube type radiator with silicone coolant and
heater hoses. Brazed aluminum charge-air cooler.
Fuel Tank: 50-gal. (189L) fuel tank with in-line filter.
Optional Carrier Engine
Cummins ISC-300 turbo-charged, charge-air cooled, 6-cylinder,
4-cycle, liquid cooled, isolation-mounted diesel engine. 300 peak
hp (224kw) @ 2,000 rpm; peak torque 860 lbs.-ft. (1,166Nm) @
1,300 rpm; 504.5 cid (8.3L).
Carrier Air System
13.2 cfm (374CL) compressor. Bendix AD-9 desiccant type air
dryer with heated automatic ejector valve, spin-on cartridge.
Transmission
Eaton Fuller RT8908LL manual, 10 speeds forward, 3 reverse
with Spicer 14" (356mm) diameter two-disc hydraulic clutch. Air
operated countershaft brake and multi-mesh gearing.
Transfer Case: Fabco TC170 with cab-controlled front axle
disconnect
Axles
6 x 4 Front: Rockwell FF-942: 13,200lb. (5,987kg) rated capacity.
6 x 6 Front: Fabco SDA-1600: 16,000lb (7,257kg) rated capacity
with 4.88:1.00 ratio
Rear: Eaton 405 tandem: 40,000lb. (18,144kg) rated capacity.
Cab-controlled inter-axle and differential lock with 4.88:1.00 ratio.
Optional Rear Axle: Eaton 461 tandem: 46,000lb. (20,865kg) rated
capacity.
Steering
Integral hydraulic power steering
Drive Line
Spicer 1710 series needle bearing universal joints.
Suspension
Front: Two 14-leaf spring 41.5" x 3" (105cm x 7.6cm) with
mechanical stops.
Rear: Hendrickson cast steel equalizer teams with 54" (137cm)
axle center, 8" (20cm) oscillation.
Brakes
Independent front and rear service brake system incorporates
spring set emergency and air applied service and parking brakes
with automatic slack adjusters on both rear axles.
6 x 4 Front: Rockwell Cam/Master 16.5" x 5" (41.9cm x 12.7cm).
6 x 6 Front: Eaton standard Service Cam 16.5" x 5"
(41.9cm x 12.7cm)
Rear: Eaton Extended Service Cam 16.5" x 7” (41.9cm x 17.8cm).
Wheels
6 x 4 Front: Disc
6 x 6 Front: Disc
6 x 6 Rear: Disc
Tires
6 x 4 and 6 x 6: 11R-22.5 (G) 14 PR front and dual rear highway
tread
Option: 385/65R-22.5 (j) 18 PR front highway tread.
Option: 11R-22.5 (G) 14 PR dual rear traction tread.
Frame
Reinforced wide-flange “I” beams 10" x 39 lbs./ft. (25cm x
58kg/m), fully welded cross members. Bolt-on front bumper.
Carrier Cab
All-weather steel cab, isolation-mounted, acoustic-lined, with
Bostrom T-bar seat, seat belt, tinted safety glass windows with
adjustable side windows, ventilator in cowl, 2-speed electric
windshield wiper with washer, fire extinguisher, sun visor, heat
and defroster fans, and interior light.
Carrier Controls
Individual foot pedals hydraulically actuate the clutch and
mechanically actuate the dual air brake valve and engine throttle.
Once manual transmission shift lever with air-operated range
selector.
Carrier Standard Equipment
Sealed halogen high/low beam headlights with high-beam
indicator. Turn signals, clearance lights, taillights, back-up lights,
stop lights, and 4-way hazard lights. 3-light identification cluster
front and rear. Cab interior light. West-coast and convex mirrors.
Tow hooks front and rear. Dual electric horns. Dial electric travel
alarms signal remote control movement and reverse movement.
Key-operated ignition/start. Lighted gauges for engine oil pres-
sure and coolant temperature, voltage, fuel level, speedometer,
odometer, tachometer, hour meter and dual air pressure.
Audio-visual alarm system monitors: low coolant level, high
coolant temperature, and low engine oil pressure. Low air pres-
sure warning light. Push-pull air valve for emergency/parking
brakes with flashing indicator light. Disc wheels.
Carrier Options
Spark arrestor. Vandalism covers. Hydraulic stabilizers, control
in upper cab. Maintenance-free battery, air ride seat, and air
conditioning.
Upperstructure Engine
Cummins QSB4.5-Tier 3 turbo-charged, 4-cylinder, 4-cycle,
liquid-cooled, isolation-mounted diesel engine. 140 peak hp
(104kw) @ 2,300 rpm, 130 hp (97kw) @ 2,500 rpm, 459 lbs.-ft
peak torque (622Nm) @ 1,500 rpm 275 cid (4.5L), 4.21" bore x
4.88 stroke (107mm x 124mm), 17.2:1 compression ratio.
Two-stage dry-type air cleaner. Spin-on lube filter, fuel filter/water
separator. Electronically controlled fuel pump. 12 volt DC,
105 amp alternator with integral solid-state regulator. Exhaust gas
particulate filter is not required.
Battery: Two SAE 12 volt DC 600 CCA @ 0˚ F (-22˚ C).
Radiator: Fin and flat tube type radiator with box type shroud.
Brazed aluminum charge-air cooler.
Fuel Tank: 50-gal. (189L) fuel tank with in-line filter.
Upperstructure Air System
8.5 cfm (241 CL) compressor. Bendix AD-9 desiccant type air
dryer with heated automatic ejector valve, spin-on cartridge.
Hydraulic System, Fixed Flow
One 2-section tandem pump, flange mounted to the engine and
driven directly by means of a Lovejoy Centaflex coupling.
Maximum 80 gpm (364L/min.) @ 2,500 rpm, and 100˚ F (38 C) oil
temperature. Integral flow divider and relief valve provide flow for
remote steer, etc.
Four double-acting cylinders with bolt-on heads: Two boom
hoist: 5" ID (127mm), 3.25" (83mm) rod, 30.25" (768mm) stroke,
self-aligning bearings. One boom telescope: 4.5" ID (114mm),
3" (76mm) rod, 120" (3,048mm) stroke, self-aligning bearing in
rod end. One tool: 5" ID (127mm), 2.5" (63mm) rod, 18" (457mm)
stroke, self-aligning bearing in housing end. One 22 hp (16.4kw)
hydraulic swing motor with manually or automatic disc type swing
brake. One 56hp (41.8kw) hydraulic remote travel motor. Once
cylinder-type rotary actuator, 6" ID (152mm), 180˚ rotation with
cushion lock valve
Hydraulic Remote Control
Carrier powered by upperstructure engine through hydraulic
motor and P.T.O. attached to transmission. Toggle air valve to
select remote control located in carrier cab. Propel, steering levers
located in upperstructure cab.
Swing
Speed: 7.9 rpm, 0 deg to 90˚ 2.5 seconds.
Upperstructure Cab
All-weather, isolation-mounted, acoustic-lined steel cab with
tinted safety glass windows and skylight. Heater, defroster fan,
fire extinguisher, 3-way adjustable cushioned seat. Front window
self-stores in cab. Sliding rear window.
Upperstructure control
Two armrest mounted joysticks control all excavator functions.
Dead-man type self-centering: when controls are released,
machine movements stop automatically.
Remote Control: One floor mounted rocker pedal controls for-
ward/reverse carrier travel, one joystick mounted rocker switch
controls the steering. Both are dead-man type self-centering:
when pedal is centered, carrier brakes are set automatically. One
operator controlled swing-parking brake switch. Push-pull air
valve for emergency brakes.
Upperstructure Options
Vandalism protection package: metal window covers, locks for
upperstructure access doors, storage rack (or Lexan windows
less storage rack). Tachometer/hour meter. Engine coolant filter.
Pump cavitation warning light. Strobe or rotating-beacon and
indicator. Light package: two boom-mounted and two frame-
mounted halogen work lights, two tail lights on upper shroud.
Electric 2-speed windshield wiper with washer. Electric heating
element hydraulic reservoir. Kwik-change bucket adapter. Seat
belts. Air conditioning.
Buckets and Attachments
Buckets fabricated of steel plate with T-1 steel cutting edges and
wear strips, hardened steel bushings in ears, replaceable tooth
points with flex pins on excavating buckets
Ditching Buckets: 60" (152cm), 66" (168cm).
Excavating Buckets: 24" (61cm), 30" (76cm), 36" (91cm).
Specialty Buckets: 24" (61cm) V-type bucket, rounded bottom;
60" (152cm) material handling bucket; 30" (76cm) pavement
removal bucket.
Boom Extensions: 2.5' (.8m), 4' (1.2m), 90˚ Material (unloading).
Attachments: 8’ (2.4m) grading blade, single-tooth ripper, guard
rail cleanout, brush mower, grapple, magnet, hammer and auger
attachments also available.
Operating Weights
Approximate working weight of carrier and upperstructure,
including 60" (152cm) ditching bucket and full fuel tanks.
6 x 4: 39,200 lbs. (17,781kg).
6 x 6: 41,400 lbs. (18,779kg).
217 Patneaude Drive
Winona, Minnesota 55987
Phone: (507) 454-4563
Fax: (507) 453-5441
www.badgerequipment.com
Made in the USA
All specifications are subject to change.