COATS 850 Solid State Wheel Balancer - Manual (Page 7)

COATS 850SS Wheel Balancer • 1
Before You Begin
Receiving
The shipment should be thoroughly inspected as
soon as it is received. The signed bill of lading is
acknowledgement, by the carrier, of receipt in good
condition of the shipment covered by our invoice.
If any of the goods called for on this bill of lading are
shorted or damaged, do not accept them until the car-
rier makes a notation of the shorted or damaged goods
on the freight bill. Do this for your own protection.
NOTIFY THE CARRIER AT ONCE if any hidden loss or
damage is discovered after receipt and request him to
make an inspection. If the carrier will not do so, pre-
pare an affidavit to the effect that you have so notified
the carrier (on a certain date) and that he has failed to
comply with your request.
IT IS DIFFICULT TO COLLECT FOR LOSS OR DAM-
AGE AFTER YOU HAVE GIVEN THE CARRIER A CLEAR
RECEIPT.
File your claim with the carrier promptly. Support your
claim with copies of the bill of lading, freight bill,
invoice, and photographs, if possible.
Although COATS responsibility ceases upon delivery
of the shipment to the carrier, we will gladly assist in
tracing lost shipments. Our willingness to assist in
every possible manner does not make COATS respon-
sible for collection of claims, or replacement of lost or
damaged materials.
Features
• Exclusive Direct Drive System (No Belts or Pulleys)
• Single-Spin Balancing
• Vertical Wheel Mounting
• Hood Safety Interlock Switch
• Graduated Cone Assortment for Back Cone Mounting
• Self Calibrating
• Removable Stub Shaft for Closed Center Wheel
Mounting on Optional Combi-Adapter
• Extended Face Plate Flange for Deeper Wheels
• “No Bolt-Down” Installation
• Adjustable Control Panel
–Scratch and Solvent Resistant
–Large, Bright Digital Displays
–Easy-to-Read Indicators
–Large Keypad for Data Entry
–Easily Repositioned for Best Visibility
–Memory and Program Checks
–Distance and Diameter Entry
–Dynamic, Static, Alloy, & RV Balancing Modes
Specifications
• Cycle time . . . . . . . . . . . . . . . . . . 10 seconds (avg.)
• Outside Tire Diameter. . . . . . . . . . . . . . . . 40" max.
• Wheel Diameter Range . . . . . . . 10 to 24"/1016mm
• Tire Weight . . . . . . . . . . . . . . . . . . 90 pounds max.
• Wheel Diameter Range . . . 10 - 19.5"/254 - 505mm
• Wheel Width Range . . . . . 2.7 to 18.6"/68 - 472mm
• Balancing Increments . . . . . . 1/4 ounce or 5 grams
• Resolution
. . . . . . . . . . . . . . . . . . . . . . +/- 0.01 ounce (weight)
. . . . . . . . . . . . . . . . . . . . +/- 2.8 degrees (position)
• Modified High Torque Motor
. . . . . . . . . . . . . 1 HP, 180 RPM, Forced Air Cooling
• Large Housing for Heat Dissipation (Motor)
• Shipping Weight. . . . . . . . . . . . . . . . . . 437 pounds
Standard Accessories
• Graduated Cone Assortment
• Cone Spring
• Hub Nut
• No-Mar Ring
• Rim Width Calipers
• Wheel Weight Pliers
Optional Accessories
• Combi-Adapter for bolt hole mounting
• Extra Large Truck Cone Kit
• 3, 4, and, 5 Lug Universal Adapters
• Escort/Lynx Adapter
Electrical Requirements
The balancer requires a 110 VAC, 60Hz, single-phase
power supply with 20 amp fuse or circuit breaker.
This single-phase balancer is equipped with an
approved cord and a 3-prong grounding plug to fit a
Hubbell 2320 or Bryant
grounding receptacle (not
included). See figure 1.
A qualified electrician
should install the recepta-
cles in accordance with
state and local codes.
Direct Drive
Figure 1 - Outlet Wiring
Diagram