Condux Quick Connect Seal-Off - Manual (Page 2)

Universal
Seal-Off
Control Valve
Single or Double
Conduit Seal-Off
Rope Adapter
Rope
Air Hose
Optional Air
Gauge Adapter
Quick Coupler
Carrier
Wingnut
Handle
The Universal Seal-Off Control Valve Body is used with the Innerduct Seal-Off, and the Single or Double Conduit
Seal-Off. Use the interchangeable heads for the style and size you need. The Control Valve Body comes equipped
with an air flow valve and a universal hose coupling for attachment to most compressors. A 3/16in rope adapter
is included.
Single or Double Seal-Off Heads
1. Connect the Seal-Off Head to the Universal Seal-Off Control Valve using the Quick Connect Couplers.
2. Insert the rope through the rope adapter that extends from the top of the Universal Seal-Off Control Valve and
tie the line to the projectile or carrier.
3. Place the projectile or carrier into the duct and then insert the Conduit Seal-Off in the duct until the rubber seal
is inside the duct.
4. Turn the wingnut handle clockwise until it is tight. Ensure the Conduit Seal-Off is straight in the duct and the
rope adapter remains on top.
5. Close the air flow valve by turning it until it is perpendicular to the air hose coupling.
6. Attach the compressor air hose to the air hose coupling on the end of the Universal Seal-Off Control Valve.
Insert hose safety clip.
!WARNING: Always use safety clips on pneumatic hose couplings or severe personal injury could result.
Ensure the air pressure is 15psi or less.
NOTE: The optional Air Gauge Adapter (08032175) can be installed between the Seal-Off Head and the
Universal Seal-Off Control Valve to ensure air pressure does not exceed 15psi.
7. Slowly open the air flow control valve on the Universal Seal-Off Control Valve until the rope begins to feed
through the duct. This valve can also regulate the projectile or carrier speed.
Innerduct Seal-Off Heads
Connect the Seal-Off Head to the Universal Seal-Off Control Valve using the Quick Connect Couplers.
1. Insert the rope through the rope adapter that extends from the top of the Universal Seal-Off Control Valve and
tie the line to the projectile or carrier.
2. Place the projectile or carrier into the duct and then insert the Innerduct Seal-Off in the duct.
3. Twist the Innerduct Seal-Off clockwise until it seats tightly inside the duct. Ensure the rope adapter remains
on top.
4. Close the air flow valve by turning it until it is perpendicular to the air hose coupling.
5. Attach the compressor air hose to the air hose coupling on the end of the Universal Seal-Off Control Valve.
Insert hose safety clip.
!WARNING: Always use safety clips on pneumatic hose couplings or severe personal injury could result.
Ensure the air pressure is 15psi or less.
Note: The optional Air Gauge Adapter (08032175) can be installed between the Seal-Off Head and the
Universal Seal-Off Control Valve to ensure air pressure does not exceed 15psi.
6. Slowly open the air flow control valve on the Universal Seal-Off Control Valve until the rope begins to feed
through the duct. This valve can also regulate the projectile or carrier speed.
Removal Procedure
Conduit Seal-Off & Double Seal-Off:
1. Close the air flow valve at the air compressor. Wait for the pressure in the conduit and air hose to subside.
2. Disconnect the compressed air hose.
3. Loosen the Conduit Seal-Off or Double Seal-Off by turning the wing nut handle counterclockwise and pull the
Seal-Off out of the duct.
Innerduct Seal-Off:
1. Close the air flow valve at the air compressor. Wait for the pressure in the conduit and air hose to subside.
2. Disconnect the compressed air hose.
3. Loosen the Innerduct Seal-Off by twisting it counterclockwise and pull the Innerduct Seal-Off out of the duct.
Seal-Off Applications
!WARNING: Read and understand
all procedure and safety instructions
before using any Condux Innerduct
Seal-Off, Conduit Seal-Off & Double
Seal-Off. Failure to do so may result
in personal injury or property
damage. Save this user’s guide for
future reference.
!WARNING: Do not exceed 15 psi
of air pressure. Do not stand
directly behind the Seal-Off.
Serious personal injury could
result.
!CAUTION: Wear personal
protective equipment: hard hat,
safety glasses, safety shoes, and
leather work gloves.
!WARNING: Keep the compressed
air hose-couplings clean of debris.
Compressed air blows surrounding
debris during the installation and
removal of the air line. Serious
personal injury could result.
!CAUTION: Beware of sharp threads
on the seal-off head - wear leather
work gloves when handling or
personal injury could result.
Operating Procedure
!ADVERTENCIA: Favor de leer y
comprender todas las instrucciones
de operación y seguridad antes de
usar el Condux Innerduct Seal-Off,
Conduit Seal-Off & Double Seal-Off.
Si Ud. no comprende las instruccio-
nes favor de consultarle a su jefe.
ADVERTENCIA
Instrucciones
de Operación
Universal
Seal-Off
Control Valve
Innerduct Seal-Off
Rope Adapter
Rope
Air Hose
Quick Coupler
Carrier
Figure 2 - Innerduct Seal-Off Application
Figure 1 - Conduit Seal-Off Application Shown W/Optional Air Gauge Adapter
Optional Air
Gauge Adapter