Control Company 3133 COUNTER PEN - Manual

Traceable ® is a registered trademark of Control Company ©2009 Control Company. 92-3133-0 Rev. 1 031709
SPECIFICATIONS
Counting Capacity: 99,999
OPERATION
Count without Marking
1. Turn the unit on by sliding the ON/OFF switch to the ON
position.
2. With the silver pen cap in place, press the tip of the unit against
the item to be counted with sufficient pressure for the tactile
feedback “click” to be felt. The display will increment by 1 and
the unit will beep
1 .
3. Release pressure.
4. Continue to “point...press...click...release” until counting is
completed.
5. Once counting has been completed, the felt tip pen on the unit
may be used to record the count.
6. Turn the unit off by sliding the ON/OFF switch to the OFF
position. To preserve battery life, always turn the unit off when it
is not in use
3 .
Count with Marking
1. Remove the silver cap from the tip of the pen.
2. Turn the unit on by sliding the ON/OFF switch to the ON
position.
3. Press the tip of the pen against the item to be counted with
sufficient pressure for the tactile feedback “click” to be felt. The
display will increment by 1, the unit will beep
1 , and the pen will
leave a mark 2 on the counted item.
Important:
Press just hard enough for the tactile feedback “click” to be felt. Only 6.5
ounces (184 grams) of pressure is required. Do not to press so hard that the
felt tip of the pen is pushed up into the pen body.
4. Release pressure.
5. Continue to “point...press...click...release” until counting is
completed.
6. Once counting has been completed, the felt tip pen may be
used to record the count.
7. Turn the unit off by sliding the ON/OFF switch to the OFF
position. To preserve battery life, always turn the unit off when it
is not in use
3 .
8. Place the cap back on to the felt tip pen. To prevent the pen
from drying out, always replace the pen cap when the pen is not
in use.
Reset Counter to Zero
The counter may be set to zero at any time by pressing the RESET
button, or by turning the unit off.
Operational Notes
1. When pressing in rapid succession, the unit will not beep each time the
display is incremented. The display will increment each time sufficient
pressure is applied for the tactile feedback “click” to be felt.
2. The ink is water based and is not permanent. The pen will leave a small
mark on nonporous surfaces; however, the mark will be removed when
the surface is wiped, or when the ink evaporates from the surface.
3. The counter is reset to zero when the unit is turned off.
PEN CARTRIDGE REPLACEMENT
1. Remove the silver cap from the tip of the pen.
2. Grasp the tip of the unit at the four rings, turn counter clockwise
and unscrew the tip from the unit.
3. Remove the exhausted pen cartridge and replace it with a fresh
new cartridge.
4. Replace the tip of the unit and tighten securely.
5. Place the cap back on to the felt tip pen. (Use the original silver
cap, do no use the temporary cap that came with the
replacement pen cartridge.)
ACCESSORIES
Control Company Cat. No. 3135 - black
Control Company Cat. No. 3134 - green
Replacement Pen Cartridge
Control Company Cat. No. 1104 -
Replacement Battery
ALL OPERATIONAL DIFFICULTIES
If this unit does not function properly for any reason, replace the
battery with a new high-quality battery (see “Battery Replacement”
section). Low battery power can occasionally cause any number of
“apparent” operational difficulties. Replacing the battery with a new
fresh battery will solve most difficulties.
BATTERY REPLACEMENT
Erratic readings, a faint display, or no display are all indications that
the battery must be replaced. Remove the screw located on the
pocket clip on the back of the unit. Remove the back of the unit. The
battery is held in place sideways at the top of the pen. Remove the
exhausted battery and replace it with a new #392 size Silver Oxide
battery. Make certain to insert the battery with proper polarity as
indicated by the illustration in the battery compartment. Replace the
back of the unit. Replace the screw and tighten securely.
WARRANTY, SERVICE, OR RECALIBRATION
For warranty, service, or recalibration, contact:
CONTROL COMPANY
4455 Rex Road
Friendswood, Texas 77546 USA
Ph. 281-482-1714 Fax 281-482-9448
E-mail [email protected]
www.control3.com
Control Company is ISO 9001 Quality-
Certified by DNV and ISO 17025 accredited
as a Calibration Laboratory by A2LA.
COUNTER PEN™ INSTRUCTIONS