Despatch Protocol Plus Controller (Heat Only) User Manual
Ultraflex drying and firing furnace, Owner’s manual, Plus
Advertising
Protocol Plus Owner’s Manual
P
REFACE
Version 2
1
Copyright © 2010 by Despatch Industries.
All rights reserved. No part of the contents of this manual may be reproduced, copied or transmitted in any form or by any
means including graphic, electronic, or mechanical methods or photocopying, recording, or information storage and
retrieval systems without the written permission of Despatch Industries, unless for purchaser's personal use.
ULTRAFLEX DRYING AND FIRING
FURNACE
MODELS 1000, 3615, 3630, 3640
C-204
VERSION 2
10/2008
PROTOCOL
PLUS™
Controller
OWNER’S MANUAL
E-98
PN 143895
VERSION 2
12/2010
Advertising
Table of contents
Document Outline
- 1. About This Manual
- 2. Safety
- 3. Theory of Operation
- 4. Assembly & Setup
- 5. Working with Operating Modes
- 5.1. Start-up Basics
- 5.2. Manual Mode
- 5.3. Timer Mode
- 5.4. Profile Mode
- 5.5. Auto Start Mode
- 5.6. Setup Mode
- 5.6.1. Enter and Exit Setup Mode
- 5.6.2. Temperature Scale Conversion
- 5.6.3. Program Page
- 5.6.3.1. Using the Program Page
- 5.6.3.2. Programming Optional Relay Outputs
- 5.6.4. Sample Profile
- 5.6.5. Setting Up Auto Start
- 5.6.5.1. Configure Auto Start
- 5.6.5.2. Activate Auto Start
- 5.6.5.3. Deactivate Auto Start
- 5.6.6. Setting Up PID Page
- 5.6.6.1. Access the PID Page
- 5.6.6.2. Setting up Auto Tune
- 5.6.7. Setting up the Control Page
- 5.6.7.1. Access Control Page
- 5.6.8. Setting up the Communication Page
- 5.6.8.1. Access Communication Page
- 5.6.8.2. Setting up the Real Time Clock Page
- 5.6.8.3. Access Real Time Clock Page
- 5.6.9. Setting up the Relay Outputs Page
- 5.6.9.1. Access Relay Outputs Page
- 5.6.10. Setting up the Test Page
- 5.6.10.1. Access Relay Outputs Page
- 5.6.10.2. Setting up the Zone Calibration Page
- 5.6.10.3. Access Zone Calibration Page
- 5.6.10.4. Access Factory Calibration Recovery
- 5.6.10.5. Adjusting Actual Versus Displayed Parameters
- 5.6.10.6. Setting up the Sensor Calibration Page
- 5.6.10.7. Access Sensor Calibration Page
- 5.6.11. Setting up the Enable Page
- 5.6.11.1. Access Enable Page
- 5.6.12. Setting up Digital Inputs (Optional)
- 6. Maintenance
- 7. Troubleshooting: Error Messages and Alarm
- 8. Appendices
- 8.1. Quick Reference and Default Values
- 8.1.1. Program Page Default Values
- 8.1.2. Autostart Page Default Values
- 8.1.3. PID Page Default Values
- 8.1.4. Programming Table Worksheet
- 8.1.5. Control Page Default Values
- 8.1.6. Communication (Optional) Page Default Values
- 8.1.7. Real Time Clock Page Default Values
- 8.1.8. Relay Outputs (Optional) Page Default Values
- 8.1.9. Test Page Default Values
- 8.1.10. Zone Cal Page Default Values
- 8.1.11. Sensor Cal Page Default Values
- 8.1.12. Enable Page Default Values
- 8.2. Standard Products Warranty
- /