Enerpac WMC-Series - Manual

Instruction Sheet
POWERFUL SOLUTIONS. GLOBAL FORCE.
L1106 Rev. B 08/12
WHC, WMC, and WHR
Hydraulic Cutters
IMPORTANT RECEIVING INSTRUCTIONS: Visually inspect all components for shipping damage. Shipping damage is not covered
by warranty. If shipping damage is found, notify carrier at once. The carrier is responsible for all repair and replacement costs resulting
from damage in shipment.
SAFETY FIRST
Carefully plan your system by selecting components designed to perform the intended operation and which will
adequately perform with existing equipment. Always check the product limitations regarding pressure ranges, load
capacities and set-up requirements. The system operating pressure must not exceed the pressure rating of the lowest
rated component in the system. Read all CAUTIONS, WARNINGS, and INSTRUCTIONS included with, or attached to, each product.
Follow all safety precautions to avoid personal injury or property damage during the system operation. ENERPAC CANNOT BE
RESPONSIBLE FOR DAMAGE OR INJURY RESULTING FROM UNSAFE USE OF PRODUCT, LACK OF MAINTENANCE, OR
INCORRECT PRODUCT AND SYSTEM APPLICATION. Contact Enerpac when in doubt as to safety precautions or applications.
DESCRIPTION
Enerpac cutters can be used for a variety of cutting operations.
The table below lists the size and type of material your tool is
capable of cutting.
Self-contained hydraulic cutters (WMC models) are extremely
portable. Hydraulic cutterheads (WHC & WHR models)
require 10,000 psi hydraulic pumps and are recommended for
applications where many cuts must be made in a short amount
of time.
WMC-2000
WHC-750
Cutting Capacity Chart
MAXIMUM DIAMETER OF
MATERIAL (inches)
Capacity (tons)
Steel Wire Rope 6x7, 6x12,
6x19 Hempcore or IWRC
Copper Wire or Bar
Aluminum Wire or Bar
Soft Steel Bolts
Reinforcing Bar
Bare Copper Wire Strand
Bare Aluminum Wire Strand
ACSR Wire Strand
Guy Steel Wire Strands 1x7
Guy Steel Wire Strand 1x19
Telephone Cable
Underground Cable (Power)
Grade 70 or 80 Alloy Chain
Hydraulic Cutterheads
WHC
-750
4
11
16
"
11
16
"
11
16
"
11
16 "
3
4
"
3
4
"
3
4
"
5
8
"
5
8
"
WHC
-1250
20
1 1
4
"
1 1
8
"
1 1
4
"
1 1
8 "
1"
1 1
4
"
1 1
4
"
1 1
4
"
7
8
"
7
8
"
WHC
-2000
13
1"
1 1
4
"
1 1
4
"
7
8 "
2"
2"
2"
3
4
"
3
4
"
2"
WHC
-3380
3
1 5
8
"
1 11
16
"
3 3
8
"
3 3
8
"
WHC
-4000
8
4"
4"
WHR
-1250
20
1 1
4
"
1 1
8
"
1 1
4
"
1 1
8 "
1"
1 1
4
"
1 1
4
"
1 1
4
"
7
8
"
7
8
"
Self-Contained Cutters
WMC
-580
4
5
8
"
5
8
"
5
8
"
5
8
5
8
"
5
8
"
5
8
"
9
16
"
9
16
"
5
8
"
WMC
-750
4
3
4
"
11
16
"
11
16
"
11
16 "
3
4
"
3
4
"
3
4
"
9
16
"
9
16
"
11
16
"
WMC
-1000
20
3
4
"
3
4
"
3
4 "
3
4
"
1
2 "
WMC
-1250
20
1 1
4
"
1 1
8
"
1 1
4
"
1 1
4 "
7
8
"
1 1
4
"
1 1
4
"
1 1
4
"
7
8
"
1"
WMC
-1580
6
3
4
"
3
4
"
3
4
"
3
4 "
1 1
2
"
1 5
8
"
1 5
8
"
5
8
"
5
8
"
1 5
8
"
WMC
-2000
13
1"
1 1
4
"
1 1
4
"
7
8 "
2"
2"
2"
3
4
"
3
4
"
2"
WMC
-3380
3
1 5
8
"
1 11
16
"
3 3
8
"
3 3
8
"
Unit is not designed to cut this size or type of material.
Any attempt to do so will result in personal injury and/or
damage to the unit and will void the warranty.
WARNING