ERICO CADDY ROD LOCK L-Bracket User Manual
Caddy rod lock l-bracket, Instruction sheet
(1) bolt, washer & nut
(washer under nut
on opposite side)
(2) 1/4" or M6
self drill screw
or tap screw
*VdS Approval G413038. Complies with VdS®
CEA 4001 (Guidelines for Sprinkler Systems)
Chapter 15.2.3 and shall be installed in
accordance with VdS CEA 4001.
Part
Number
Article
Number
Rod Size
CRLL37EG
N/A
3/8"
CRLLM10EG*
390012
M10
CRLLM8EG*
390011
M8
(washer under nut
(1) lag screw
on opposite side)
(1) bolt, washer & nut
(2) 1/4" or M6
lag screws
All governing codes and regulations and those required by the job site must be observed.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
The customer is responsible for:
6.
www.erico.com
CFS457_F
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
CADDY ROD LOCK L-Bracket
other purpose.
SAFETY INSTRUCTIONS:
© 2012, 2013, 2014 ERICO International Corporation
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
®
a. Conformance to all governing codes.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
1 OF 2
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.
c. Using appropriate industry standard hardware as noted above.
TECHNICAL SUPPORT:
INSTRUCTION SHEET
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.com and from your ERICO customer service representative.
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be completely followed to ensure proper and safe installation and performance.
3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
FM is a registered certification mark of FM Approvals LLC, LTD.
UL is a registered trademark of UL LLC
VdS is a registered trademark of VdS Schadenverhütung GmbH
lbs
N
Concrete
1/2"
1
4" or DN100
4" or DN100
700
3114
1/2" x 3" lag screw
1
4" or DN100
4" or DN100
600
2669
1/2" bolt, nut, washer
1
4" or DN100
4" or DN100
700
3114
1/4" x 1-1/2" lag screw
2
N/A
N/A
300
1334
Min. 16 Ga. [1.5mm] Steel
1/2" bolt, nut, washer
1
4" or DN100
4" or DN100
700
3114
1/2" bolt, nut, washer
1
4" or DN100
4" or DN100
700
3114
1/4" x 1" self drill or tap screw
2
4" or DN100
3-1/2" or DN90
700
3114
Min. 12 Ga. [3mm] Steel
1/4" x 1" self drill or tap screw
2
4" or DN100
4" or DN100
700
3114
Concrete
M10
1
4" or DN100
4" or DN100
700
3114
M10 x 80mm lag screw
1
2" or DN50
2" or DN50
600
2669
M10 bolt, nut, washer
1
4" or DN100
4" or DN100
700
3114
M6 x 40mm lag screw
2
N/A
N/A
300
1334
Min. 16 Ga. [1.5mm] Steel
M10 bolt, nut, washer
1
4" or DN100
4" or DN100
700
3114
M10 bolt, nut, washer
1
4" or DN100
4" or DN100
700
3114
M6 x 25mm self drill or tap screw
2
4" or DN100
3-1/2" or DN90
700
3114
Min. 12 Ga. [3mm] Steel
M6 x 25mm self drill or tap screw
2
4" or DN100
4" or DN100
700
3114
Concrete
M10
1
N/A
N/A
500
2224
M10 x 80mm lag screw
1
N/A
N/A
500
2224
M10 bolt, nut, washer
1
N/A
N/A
500
2224
M6 x 40mm lag screw
2
N/A
N/A
300
1334
Min. 16 Ga. [1.5mm] Steel
M10 bolt, nut, washer
1
N/A
N/A
500
2224
Min. 14 Ga. [2mm] Steel
M6 x 25mm self drill or tap screw
2
N/A
N/A
500
2224
Max. FM®1951
pipe size (NPS)
UL2239/ MSS/ General
Min. 14 Ga. [2mm] Steel
Structure
Fastener Type
Fastener
Quantity
Max. UL®203
pipe size (NPS)
Wood
Part Number
(Article Number)
CRLL37EG
CRLLM10EG
(390012)
Min. 14 Ga. [2mm] Steel
Wood
CRLLM8EG
(390011)
Wood