ERICO CADDY ROD LOCK Strut Nut - Manual

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
CADDY® ROD LOCK Strut Nut
www.erico.com CFS500_A
INSTRUCTION SHEET
1 OF 2 © 2014 ERICO International Corporation.
TECHNICAL SUPPORT:
3/8", M8, M10
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at 1.
www.erico.com and from your ERICO customer service representative.
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be completely followed to ensure proper and safe installation and performance. 3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property 4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any 6.
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified
engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
Rotation Only
Untighten
stem nut
Remove insert to allow the
Strut Nut to slide and
rotate in the slot of the strut
Configuration #2
CRLSSxxEG
Insert allows for the
Strut Nut to rotate in
the slot of the strut
Sliding and Rotation
Untighten
stem nut
Configuration #1
Strut Edge Distance Requirement
Min of 1" [25mm] @ both strut ends
9/16" or 14mm
CRLSLxxEG
Part Number
Article
Number
Rod Size
Strut Channel
Profile
Strut Channel
Thickness
Required strut
slot width*
Load Rating
CRLSL37EG N/A 3/8" A - Type 12 Ga 9/16" 1,500 lbs
CRLSS37EG N/A 3/8" C - Type 14 Ga 9/16" 900 lbs
1.5 mm 14 mm 3,400 N
2.0 mm 14 mm 4,000 N
2.5 mm 14 mm 4,900 N
1.5 mm 14 mm 3,400 N
2.0 mm 14 mm 4,000 N
2.5 mm 14 mm 4,900 N
1.5 mm 14 mm 3,400 N
2.0 mm 14 mm 4,000 N
2.5 mm 14 mm 6,200 N
1.5 mm 14 mm 3,400 N
2.0 mm 14 mm 4,000 N
2.5 mm 14 mm 6,200 N
* ERICO® offers CADDY® ERISTRUT having 14mm slot width.
CRLSLM10EG 390042 M10 A - Type
CRLSSM10EG 390044 M10 C - Type
CRLSLM8EG 390041 M8 A - Type
CRLSSM8EG 390043 M8 C - Type