ERICO Branch Line Restraint Device User Manual
ERICO Accessories for electrical
(XX)= Finish Specifier
Restraint devices are intended to be installed in accordance with NFPA®-13 and the manufacturer's installation instructions.
UL Listed with lightwall (Commonly referred to as Schedule 7) Dyna-Flow
®
FM Load rating for Schedule 40 may be applied to EN 10255 (DUB 2441) and JIS G3454 pipe.
FM Load rating for Schedule 10 may be applied to GB/T 3091, GB/T 3092 and FM Approved
Thinwall Pipe and EN 10255 M (DIN 2440), JIS G3452 pipe.
FM Load rating for lightwall may also be applied to GB/T 8163 and EN 10220 (DIN 2448).
Installation using a drill or impact drive
should not exceed a drive speed of
1500 rpm. Exceeding 1500 rpm drive
speed may cause stripping of the thread.
NA Part
Number
EU Article
Number
Service Pipe Size NB/DN
Rod Size
UL® Load Rating
FM® Load Rating
Lightwall/
Schedule 10/40
Lightwall/Schedule 10/40
Inch
mm
45°-59°
60°-74°
75°-90°
CSBBRP100XX
404477
1"
25
3/8", [M10]
475lbs [2113N]
170lbs [755N]
210lbs [935N]
230bs [1025N]
1/2", [M12]
190lbs [845N]
240lbs [1070N] 270lbs [1200N]
CSBBRP125XX
404478
1-1/4"
32
3/8", [M10]
170lbs [755N]
210lbs [935N]
230bs [1025N]
1/2", [M12]
190lbs [845N]
240lbs [1070N] 270lbs [1200N]
CSBBRP150XX
404479
1-1/2"
40
3/8", [M10]
190lbs [845N]
240lbs [1070N] 270lbs [1200N]
1/2", [M12]
150lbs [665N]
190lbs [845N]
210lbs [935N]
CSBBRP200XX
404480
2"
50
3/8", [M10]
190lbs [845N]
240lbs [1070N] 270lbs [1200N]
1/2", [M12]
150lbs [665N]
190lbs [845N]
210lbs [935N]
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
CFS449_E
INSTRUCTION SHEET
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
1 OF 2
© 2011, 2012 ERICO International Corporation
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.com and from your ERICO customer service representative.
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be completely followed to ensure proper and safe installation and performance.
3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
Dyna-Flow is a registered trademark of Allied Tube & Conduit Corporation
FM is a registered certification mark of FM Approvals LLC, LTD
NFPA is a registered trademark of National Fire Protection Association, Inc.
UL is a registered trademark of UL LLC