ETC Source Four XT HID Zoom Wall Mount User Manual
Installation electrical, Lamp and ballast information
Page 1 of 2
Corporate Headquarters 3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA Tel +608 831 4116 Fax +608 836 1736
London, UK Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK Tel +44 (0)20 8896 1000 Fax +44 (0)20 8896 2000
Rome, IT Via Pieve Torina, 48, 00156 Rome, Italy Tel +39 (06) 32 111 683 Fax +44 (0) 20 8752 8486
Holzkirchen, DE Ohmstrasse 3, 83607 Holzkirchen, Germany Tel +49 (80 24) 47 00-0 Fax +49 (80 24) 47 00-3 00
Hong Kong Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong Tel +852 2799 1220 Fax +852 2799 9325
Service: (Americas)
(UK)
(DE)
(Asia)
Web:
www.etcconnect.com
Copyright © 2013 ETC. All Rights Reserved. Product information and specifications subject to change.
7065M2130
Rev B Released 2013-10
ETC intends this document to be provided in its entirety.
● The fixture must be installed by a qualified electrician.
● The fixture must be installed in accordance with national, state, and local electrical codes.
● The fixture must be grounded.
● An application-appropriate electrical junction box is required.
● The junction box must not interfere with aiming or re-lamping the fixture.
● The fixture is completely pre-wired at the factory and there is no need for entry into the ballast housing.
● The lamp and ballast voltage must match the supply voltage.
● The fixture cannot be connected to a dimmer. Dimming will damage the ballast and void the warranty.
Lamp and Ballast Information
● Acceptable voltage is either 120V or 277V (±10%) 50/60 Hz only, depending on the model purchased.
● Refer to the User Manual for information about HID lamps.
● 120V (nominal) Ballast
– 120V ±10%, 60Hz
– 1.5 Amps operating current
● 277V (nominal) Ballast
– 277V ±10%, 60Hz
– 0.61 Amps operating current
Installation
Electrical
The Wall Mount Bracket accessory for the Source Four XT HID provides a stable mounting position for the
fixture, while providing a wire way for a clean and functional installation to walls and other vertical surfaces.
Install on a suitable, rigid wall. The installation must meet the published weight and wind-load requirements
for the fixture. Use application appropriate bolts, nuts, and washers such as hot-dipped zinc or stainless
steel for wet locations.
●
Weight: All weights are exclusive of accessories, color filters, and patterns.
15-30: 39 pounds
25-50: 34.5 pounds
●
Wind Load:
15-30: 1.4 square feet of effective projected area (EPA).
25-50: 1.15 square feet of effective projected area (EPA).
Use two bolts to attach the fixture to the Wall Mount. The curved holes in the yoke allow small aiming
adjustments.
Reference Source Four XT HID Installation Instructions and Source Four XT HID Long Yoke Installation
Instructions for information about electrical requirements and installing the fixture. Both instructions include
a full-sized yoke template and are available for download at www.etcconnect.com.
Keep the following in mind while installing the fixture and Wall Mount.
● The yoke must be mounted on the fixture with the bracing towards the ballast end. Refer to the
illustration on the next page.
● The slots on the yoke provide small aiming adjustments.
● The fixture must be attached to the mount and the power cord pulled through the cable grip prior to
mounting the assembly on the wall.
● The Wall Mount must be securely attached to the wall directly over a junction box.
● Use an appropriate water-resistant sealant around the junction box.
● The fixture and mount assembly is heavy. Take the necessary precautions to ensure your safety.
See the reverse side of this document for step-by-step wall mounting instructions.
15-30
25-50
CAUTION: The fixture is sold for either 120V or 277V to match your power supply. Verify that
the lamp and ballast voltage requirements matches the power supply. Connecting the fixture to
the wrong voltage voids the warranty.
NOTE: Reference the Source Four XT HID Zoom User Manual for information
about lamp replacement, adjusting the light beam, and cleaning the fixture. The
User Manual is available for download at www.etcconnect.com.
WARNING:
● Do not use this fixture if glass lens is deeply scratched or cracked. Damaged
lenses must be replaced.
● Do not mount the fixture on or near combustible surfaces.
Failure to follow these warnings can result in serious injury or death.
Installation Instructions
Source Four XT HID Zoom Wall Mount
15-30 and 25-50 Zoom
WARNING:
● Do not use this fixture with a damaged power lead. If the power lead (cordset)
is damaged, it must be replaced.
● Do not expose the interior of the fixture to moisture. Do not stand in water
while installing or servicing the fixture.
Failure to follow these warnings can result in serious injury or death.
WARNING:
● Do not use the fixture with a damaged power lead. If the power lead (cordset)
is damaged, it must be replaced.
● Do not expose the interior of the fixture to moisture. Do not stand in water
while installing or servicing the fixture.
Failure to follow these warnings can result in serious injury or death.