ETC Source Four XT HID Zoom Installation Instructions User Manual
Installation instructions, Source four xt hid zoom, Unpacking
15-30 and 25-50 Zoom
Installation Instructions
Page 1 of 2
Corporate Headquarters 3031 Pleasant View Road, P.O. Box 620979, Middleton, Wisconsin 53562-0979 USA Tel +608 831 4116 Fax +608 836 1736
London, UK Unit 26-28, Victoria Industrial Estate, Victoria Road, London W3 6UU, UK Tel +44 (0)20 8896 1000 Fax +44 (0)20 8896 2000
Rome, IT Via Pieve Torina, 48, 00156 Rome, Italy Tel +39 (06) 32 111 683 Fax +44 (0) 20 8752 8486
Holzkirchen, DE Ohmstrasse 3, 83607 Holzkirchen, Germany Tel +49 (80 24) 47 00-0 Fax +49 (80 24) 47 00-3 00
Hong Kong Rm 1801, 18/F, Tower 1 Phase 1, Enterprise Square, 9 Sheung Yuet Road, Kowloon Bay, Kowloon, Hong Kong Tel +852 2799 1220 Fax +852 2799 9325
Service: (Americas)
(UK)
(DE)
(Asia)
Web:
www.etcconnect.com
Copyright © 2013 ETC. All Rights Reserved. Product information and specifications subject to change.
7065M2100
Rev C Released 2013-10
Unpacking
Remove the fixture from the carton and remove all packing materials. Remove the barrel to remove the
internal foam packing materials.
Removing and Installing the Barrel
To remove the barrel:
Step 1: Loosen the three 4mm hex screws around the barrel.
There is a nylon retaining washer on each screw to prevent it from slipping out of the ballast
housing.
Step 2: Slide the barrel off the fixture.
Step 3: Hang the barrel on the yoke or set it safely aside.
To install the barrel:
Step 1: Slide the barrel down over the lens rails, aligning the top ridges of the barrel with the top ridges of
the housing.
Step 2: Tighten the three 4mm hex screws around the barrel.
Partially tighten each screw, working progressively around the barrel until all have been
tight ened to 25in-lbs (2.82 Nm).
The nylon washer should be tightly sandwiched between the two flanges at each scew
connenction.
Install on a suitable, rigid permanent base with secured bolts. This can include poured concrete pads, factory-supplied
pole-top and wall-mount brackets, and other attachments which meet the published weight and wind-load requirements for
the fixture. For ground-mounting, reference the template and notes included on the reverse of these installation instructions.
●
Weight: All weights are exclusive of accessories, color filters, and patterns.
15-30: 39 pounds
25-50: 34.5 pounds.
●
Wind Load
15-30: 1.4 square feet of effective projected area (EPA).
25-50: 1.15 square feet of effective projected area (EPA).
● The fixture must be installed by a qualified electrician.
● The fixture must be installed in accordance with national, state, and local electrical codes.
● The fixture must be grounded.
● An application-appropriate electrical junction box with cord grips are required.
● The junction box must not interfere with aiming or re-lamping the fixture.
● The fixture is completely pre-wired at the factory and there is no need for entry into the ballast housing.
● The lamp and ballast voltage must match the supply voltage.
● The fixture cannot be connected to a dimmer. Dimming will damage the ballast and void the warranty.
Lamp and Ballast Information
Acceptable voltage is either 120V or 220V - 277V (±10%) 50/60 Hz only, depending on the model purchased.
Refer to the User Manual for information about HID lamps.
● 120V (Nominal) Ballast:
- 120V ±10%, 60Hz
- 1.5 Amps operating current
● 220V, 230V (50Hz), 240V, 277V (Nominal) Ballast:
- 277V ±10%, 60Hz
- 220V, 230V, 240V ±10%, 50Hz/60Hz
- 0.61 Amps operating current at 277V
- 0.69 Amps operating current at 230V
Installation
Electrical
Barrel
4mm hex
screw (3)
Standard yoke
Reflector
housing
Remove or install barrel
Source Four XT HID Zoom
WARNING:
● Do not use this fixture if glass lens is deeply scratched or cracked. Damaged lenses must be
replaced.
● Do not mount the fixture on or near combustible surfaces.
Failure to follow these warnings can result in serious injury or death.
WARNING:
● Do not use this fixture with a damaged power lead. If the power lead (cordset)
is damaged, it must be replaced.
● Do not expose the interior of the fixture to moisture. Do not stand in water
while installing or servicing the fixture.
Failure to follow these warnings can result in serious injury or death.
CAUTION: The fixture is sold for either 120V or 277V to match your power supply. Verify that
the lamp and ballast voltage requirements matches the power supply. Connecting the fixture to
the wrong voltage voids the warranty.
CAUTION: Remove foam packing from internal lenses before connecting power
to the fixture.
NOTE: Reference the Source Four XT HID Zoom User Manual for information
about lamp replacement, adjusting the light beam, and cleaning the fixture. The
User Manual is included in the carton and available for download at
www.etcconnect.com.