Bolens BL250 - Manual (Page 4)

4
• IMPORTANT SAFETY INFORMATION •
• Move the unit at least 30 feet (9.1 m) from the fueling
source and site before starting the engine. Do not smoke.
Keep sparks and open flames away from the area while
adding fuel or operating the unit.
WHILE OPERATING
• Never start or run the unit inside a closed room or building.
Breathing exhaust fumes can be fatal. Operate this unit
only in a well-ventilated outdoor area.
• Wear safety glasses or goggles that meet ANSI Z87.1 stan-
dards and are marked as such. Wear ear/hearing protection
when operating this unit. Wear a face or dust mask if the
operation is dusty.
• Wear heavy long pants, boots, gloves and a long sleeve
shirt. Do not wear loose clothing, jewelry, short pants, san-
dals or go barefoot. Secure hair above shoulder level.
• The cutting attachment shield must always be in place while
operating the unit. Do not operate unit without both trim-
ming lines extended, and the proper line installed. Do not
extend the trimming line beyond the length of the shield.
• This unit has a clutch. The cutting attachment remains sta-
tionary when the engine is idling. If it does not, have the
unit adjusted by an authorized service technician.
• Adjust the J-handle to your size in order to provide the best
grip.
• Be sure the cutting attachment is not in contact with any-
thing before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position when-
ever pulling the starter rope. Both the operator and unit
must be in a stable position while starting. Refer to the
Starting/Stopping Instructions.
• Use the right tool. Only use this tool for its intended purpose.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating.
Keep a firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all moving
parts. Do not touch or try to stop the cutting attachment
when it rotates.
• Do not touch the engine, gear housing or muffler. These
parts get extremely hot from operation, even after the unit
is turned off.
• Do not operate the engine faster than the speed needed to
cut, trim or edge. Do not run the engine at high speed
when not cutting.
• Always stop the engine when cutting is delayed or when
walking from one cutting location to another.
• If you strike or become entangled with a foreign object,
stop the engine immediately and check for damage. Do
not operate before repairing damage. Do not operate the
unit with loose or damaged parts.
• Stop the unit, switch the engine to off, and disconnect the
spark plug for maintenance or repair.
• Use only Genuine Factory Part™ replacement parts and
accessories for this unit. These are available from your
authorized service dealer. Use of any non-original factory
parts or accessories could lead to serious injury to the user,
or damage to the unit, and void your warranty.
• Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment and shield.
• To reduce fire hazard, replace a faulty muffler and spark
arrestor. Keep the engine and muffler free from grass,
leaves, excessive grease or carbon build up.
WHILE OPERATING WITH CUTTING BLADE
• Read and understand all safety warnings before operating
this unit.
• Always use the shoulder harness when using the brush
blade accessory.
• Keep the J-handle between the operator and cutting
attachment or blade at all times.
• NEVER cut when the cutting blade is 30 inches (76 cm) or
more above the ground level.
• Blade thrust may occur when the spinning blade contacts
an object that it does not immediately cut. Blade thrust can
be violent enough to propel the unit and/or operator in
any direction, possibly causing a loss of control. Blade
thrust can occur without warning if the blade snags, stalls
or binds. This is more likely to occur in areas where it is dif-
ficult to see the material being cut.
• For operation with the brush blade, do not cut anything
thicker than 1/2 inch or a violent kickback could occur.
• Do not attempt to touch or stop the blade when it is rotating.
• A coasting blade can cause injury while it continues to spin
after the engine is stopped or the throttle trigger is
released. Maintain proper control until the blade has com-
pletely stopped rotating.
• Do not run the unit at high speed when not cutting.
• If you strike or become entangled with a foreign object, stop
the engine immediately and check for damage. Have any
damage repaired before attempting further operations. Do
not operate unit with a bent, cracked or dull blade. Discard
blades that are bent, warped, cracked or broken.
• Do not sharpen the cutting blade. Sharpening the blade
can cause the blade tip to break off while in use. This can
result in severe personal injury. Replace the blade.
• Do not use the cutting blade for edging or as an edger; severe
personal injury to yourself or others may incur. Use the cutting
blade only for the purpose as described in this manual.
• Stop the engine IMMEDIATELY if you feel excessive vibra-
tion. Vibration is a sign of trouble. Inspect thoroughly for
loose nuts, bolts or damage before continuing. Repair or
replace affected parts as necessary.
After Use
• Clean cutting blades with a household cleaner to remove any
gum buildup. Oil the blade with machine oil to prevent rust.
• Lock up and store the cutting blade in an appropriate area
to protect the blade from unauthorized use or damage.
OTHER SAFETY WARNINGS
• Never store a fueled unit inside a building where fumes
may reach an open flame or spark.
• Allow the engine to cool before storing or transporting. Be
sure to secure the unit while transporting.
• Store the unit in a dry area, locked up or up high to prevent
unauthorized use or damage, out of the reach of children.
• Never douse or squirt the unit with water or any other liq-
uid. Keep handles dry, clean and free from debris. Clean
after each use, see Cleaning and Storage instructions.
• Keep these instructions. Refer to them often and use them
to instruct other users. If you loan someone this unit, also
loan them these instructions.
SAVE THESE INSTRUCTIONS
RULES FOR SAFE OPERATION