General Machine Products 10500 G Cable Lasher w/Chest - Manual (Page 4)

GMP G Lasher
4
Important
precautions The proposed cable run should be pre-surveyed to deter-
mine the terrain and field conditions that will be encoun-
tered in the lashing operation. Among those factors to be
considered (not by limitation) are:
(a) vehicle & pedestrian safety
(b) condition of poles, anchors, guys and strand
(c) proper bonding and grounding of strand
and attachments
(d) obstructions such as trees, limbs and
drop wires
(e) clearances and separations on poles shared by
other utilities
(f) clearances over roads, driveways, walkways
and crossings
Protect your work site with advance warning devices at
strategic points to warn traffic and pedestrians of the
obstruction in the area.
Check your machine first!
Prior to using the machine, check that it is in good repair,
that all of the parts and mechanical assemblies are intact
and in good working order. If the machine has not been
properly maintained it may well be unsafe to use and pose
unnecessary risk to the user. GMP Lashers can be profes-
sionally repaired and/or overhauled at the factory with
quick turnaround and minimal downtime.
Use the proper safety equipment!
Before working aloft, inspect all your climbing and safety
equipment to make certain it is in good repair. And while
you are aloft, ALWAYS wear a body belt with a safety
strap securely attached to help prevent you from falling.
Also, you should always raise and lower your lasher only
with a proper aerial handline (such as our 68590 or
08192) or a truck lift.
Use the bridle assembly at pole transfers!
When transferring the lasher around a pole or other
obstruction, use the bridle assembly as a tether to prevent
damage to the machine in case it is dropped. This also
allows you to concentrate on your own safety first rather
than the safety of the machine.
13
G1 Gear Housing 05475
G2 Gear Housing Cover 05525
G3 Towing Bridle Assembly 07357
G4 Towing Bridle Stop Bolt 09007
Towing Bridle Stop Nut 03569
G5 Strand Drive Wheel 05486
G6 Strand Drive Wheel Nut 03039
G7 Pulling Eye
13398
G8 Top Roller Assembly Screw 03305
Top Roller Assembly Washer 16005
G9 Top Roller Assembly 15192
G10 Pulling Eye Screw 16041
Pulling Eye Nut 02854
G11 Clamping Washer 05485
G12 Rear Strand Drive Shaft 07363
(shaft, gears & bearing)
G13 Front Strand Drive Shaft 07364
(shaft, gear & bearing)
G14 Ratchet Pawl Spring 03037
G15 Rubber Sleeve 03041
G16 Steel Guide 05502
G17 Shoulder Screw 05527
Shoulder Nut 03272
G18 Ratchet Brake Pawl 07346
G19 Idler Gear 05496
G20 Oilite Bearing 03056
G21 Idler Gear Shaft 03038
G22 Clamping Nut 03030
G24 Ratchet Brake Collar 05531
G25 Ratchet Brake Copper Latch 05532
G26 Tru-Arc Ring #50
03277
G27 Drive Shaft 05510
G28 Collar 05535
G29 Timing Gear 25224
G30 Drive Shaft Gear Assy. 07362
G31 Spring Screw 03040
G32 Towing Bridle Pivot 05501
G33 Spacer 05534
G34 Stop Pin 09463
G35 Retaining Ring Screw 03291
Retaining Ring Lockwasher 03260
G36 88013 Bearing 03054
G37 Bearing Retainer Rings
3 ea. required 03024
2 ea. required 03025
1 ea. required 24825
G38 Tru-Arc Ring #125 09447
G39 Towing Bridle Spring 05530
G40 Pivot Retaining Ring 15220
G41 5-40 x 3 ⁄
4
Filister Screw 17677
G42 5-40 x 5 ⁄
8
Flathead Screw 09442
G43 Strand Lifter Assembly 07302
G44 10-24 x
5 ⁄
8
Filister Screw 03298
G45 Wire Coil Door Assembly 07305
G46 Door Pulley
14413
G47 Door Pulley Bearing 09435
G48 Door Release Spring 24991
G50 Handle 05506
G51 1 ⁄
4
x 20 Flathead Screw 03271
G52 .065 in. Wire Pulley 15622
G53 Front Plate Assembly 15163
G54 Left Lock 03121
G55 Right Lock 03120
G56 10-24 x 1 ⁄
2
Filister Screw 03298
G57 Locking Bolt 07580
G58 Locking Bolt Spring 03089
G59 Locking Bolt Retainer 03090
G60 Locking Bolt Retainer Nut 03087
G61 Rotor Body
05474
G62 Ring Gear 05491
G63 1 ⁄
4
-20 x 1 Allen Screw 17542
G64 Spacer 05481
G65 Strand Roller w/Bearings 26076
G66 Strand Roller Shaft
05495
G67 1 ⁄
4
-20 x 1 Flathead Screw 03271
G68 Rear Plate Assembly 07307
G69 Swing Bolt Spring 03078
G70 Swing Bolt Assembly 07547
G71 Front Bearing Ring 05478
G72 Rear Bearing Ring 05479
G73 6-32 x 3 ⁄
8
Filister Screw 03293
G74 Ball Bearing 88038 26051
G75 Eccentric Screw 03091
G76 Wire Guide Assembly 07312
G77 10-24 x 7 ⁄
8
Filister Screw 03300
G78 Front Cable Lifter Assembly 07319
G79 Hex Head Screw
03375
G80 10-24 x 1- 1 ⁄
8
Filister Screw 09440
G81 10-24 x 3 ⁄
4
Filister Screw 03299
G82 Side Roller Assembly 15191
G83 10-24 x 3 ⁄
4
Filister Screw 03299
G84 Rear Lifter Assembly 07310