HiRO H50147 - Manual (Page 2)

How to operate
Main mouse button
1.Right mouse button
2.White screen
1.Left mouse button
2. Black screen
Laser mode indicator
Laser beam
1. Laser
2. Laser On/Off
Up
1. F5/ESC
2.Link
1. Down
2. Alt+Tab
Fn
Key How to operate
1. Press and hold Fn + On/Off together for 2 seconds until the laser
mode indicator start blinking to activate the laser function. Do
the same process to turn off the laser function.
2. When laser function is on, press Laser key to shoot the laser beam.
Note: Laser function will auto shut down after press the laser button more
than 30 seconds or after 30 minutes idling time.
1. Click as right mouse function.
2. Press Fn and Right mouse button simultaneously to turn the
whole screen white. Do the same process to return to normal slide
screen.
The Fn key is used in combination with another key to perform a
specific function.
Note: The Fn key should be pressed before clicking the other desired key.
Push up the switch and go back to the previous slide.
1. Click to start the slide show. Press and hold more than three
seconds to exit the slide show.
2. To link the presenter with receiver, please see“How to re-pair the
Presenter" .
1.Pull down the switch and go to the next slide.
2.Press and hold Fn button, pull down the switch(Alt+Tab) to select
the file, then release Fn button to swap to the file selected.
Main mouse
1.Right mouse
2.White screen
Laser
Up
1.F5/ESC
2.Link
1.Down
2.Alt+Tab
Fn
1.Left mouse
2.Black screen
Slightly put your thumb on the main mouse button, rotating the thumb
to control the mouse cursor.
1. Click as left mouse function.
2. Press Fn and Left mouse button simultaneously to turn the whole
screen black. Do the same process to return to normal slide screen.
Link indicator
USB Plug
ID link button
No blink: Laser function off
Blinking: Laser function on Laser mode
indicator
FEDERAL COMMUNICATIONS COMMISSION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiated radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
Doc No.: EB-A1050-202
Frequency range : 2400~2483MHz (16 channels and 65,535 IDs per channel)
Remote range : Approx. 100 ft (30m) indoors, 328 ft (100m) outdoors
Operating voltage : Remote Control 2.4V~3.3V
Laser Pointer 2.6V~3.3V
Power : AAA battery * 2
Very low power consumption : Normal operation < 10mA
Laser operation <20mA
Sleep < 10uA
Output power : Under 1mW
Presenter dimension : 130(l) x 38.2(w) x 21.2(h) mm
Receiver dimension : 68.15(l) x 13(w) x 10.3(h) mm
Presenter weight : Approx. 60 grams (include batteries)
Receiver weight : Approx. 8 grams
Operating temperature : 0℃ (32℉) ~60℃ (140℉)
Operating humidity (non-condensing) : 10%~85% RH
laser :
Wavelengthλ= 650 nm, emission duration: continuous
Laser output power：Max. 0.95mW
Note: Design and specifications are subject to change without notice.
Product Specifications
Other information
This product is carrying the CE-Mark in accordance with the related European Directives.
EU DECLARATION OF CONFORMITY
RoHS