JUMO 60.3031 Surface-mounting thermostats, ATH.-SE Data Sheet User Manual
Page 3
Data Sheet 603031
2013-03-08/00309799
Page 3/6
JUMO GmbH & Co. KG
Delivery address: Mackenrodtstraße 14
36039 Fulda, Germany
Postal address:
36035 Fulda, Germany
Phone:
+49 661 6003-0
Fax:
+49 661 6003-607
E-mail:
Internet:
www.jumo.net
JUMO Instrument Co. Ltd.
JUMO House
Temple Bank, Riverway
Harlow, Essex CM20 2DY, UK
Phone: +44 1279 635533
Fax:
+44 1279 635262
E-mail:
Internet: www.jumo.co.uk
JUMO Process Control, Inc.
6733 Myers Road
East Syracuse, NY 13057, USA
Phone: 315-437-5866
1-800-554-5866
Fax:
315-437-5860
E-mail:
Internet: www.jumousa.com
Operating data
Case
Process connection
Note:
Physical and toxic features of the expansion means, which could occur in the event of a measuring system break.
1
There is currently no statement by the health authority concerning hazards to health in the event of short-term exposure
and low concentration, e.g. measuring system break.
Hysteresis
in % of the control /
limit value range
Rated value
Possible process value
Designation
3
3-4
S1
6
6-8
S2
1.5
1-2
S3
Switching point accuracy
in % of the control/limit val-
ue range
TW: in the upper third of the scale ± 1.5%
STB, STW (STB): in the upper third of the scale +0/-5%
Ambient temperature in-flu-
ence referring to the con-
trol /
limit value range
When the ambient temperature on the case deviates from the calibration ambient temperature 22 °C,
a switch point offset occurs.
Higher ambient temperatures = lower switching point
Lower ambient temperature = higher switching point
For devices with scale limit value
< 200 °C
÷ 200 °C
ATH.-SE-2
ATH.-SE-20
ATH.-SE-70
ATH.-SE-2
ATH.-SE-20
ATH.-SE-70
on case
0.08%/K
0.17%/K
0.06%/K
0.13%/K
on capillary per m
0.047%/K
0.054%/K
0.09%/K
0.11%/K
admissible storage tem-
perature
-50 to 50 °C
admissible ambient
temperature during use
max. +80 °C
Rated position
as per DIN 16 257, NL 0 to NL 90 (different rated positions (NL) on request)
Case
Aluminum die cast case
Surface with impact resistant textured paint:
Lid: RAL 7032, bottom section: RAL7015
Set point adjustment
The switching point can be adjusted by means of a screwdriver once the case lid has been removed
Protection class
EN 60 529-IP 54
Weight
ATHf-SE-... approx. 0.70 kg
ATHs-SE-...approx. 0.65 kg with screw-in sheath "20“
ATHs-SE-...approx. 0.85 kg with screw-in sheath and intermediate piece "30“
Type series
ATHs-SE-..
with rigid shaft
Scale limit value up to 150 °C
Sheath "20“
Scale limit value exceeding 150 °C
Sheath "30“
Screw-in sleeve with screw-in spigot G 1/2
form A as per DIN 3852/2
Screw-in sleeve with screw-in journal G 1/2
form A as per DIN 3852/2
and intermediate piece
to ensure that the max. admissible ambient temperature
of +80 °C is not exceeded on the case
Type series
ATHf-SE-..
with capillary
plain cylindrical probe "10“ (standard)
Screw-in sheath "20" (on request)
Screw-in sleeve with screw-in spigot G 1/2 form A as per DIN 3852/2
and clamping piece with locking screw to lock the probe
Material
Sheath "20“
Sheath "30“
up to +150 °C CuZn as standard
over +150 °C CrNi as standard
over +150 °C CrNi as standard
Fitting length S
(max. 200 mm)
Standard lengths: 100, 120, 150 (material CuZn, CrNi)
with 200 mm CuZn only
Immersion tube Ø
D = 8 mm, D = 10 mm
Control range
with scale limit value
Hazardous re-
actions
Fire and explosion hazard
hazardous
to waters
Information about toxicology
Ignition
temperature
Explosion limit
irritant
dangerous to
health
toxic
< +200 °C
no
+ 355 °C
0.6 -8 V%
Yes
Yes
1
no
≥
200 °C
≤ +300 °C
no
+ 490 °C
- -
Yes
Yes
1
no