Kuryakyn 7284 TRI-LINE GAUGE TRIM - Manual

THANK YOU FOR CHOOSING K ϋ RYAKYN!
PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAM-
AGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAU-
TIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF THIS
PRODUCT.
MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
1 Tri-Line Gauge Trim
1 Alcohol Pad
1 Installation instructions
TOOLS SUGGESTED:
Warm soapy water and a clean rag
STEP 1
Read and understand all steps in the instructions before starting the installation.
Park the motorcycle on a hard, level surface and turn off the ignition.
STEP 2
Refer to PIC 1. Using warm soapy water and a clean rag, remove all dirt and debris
from the installation area (in blue); allow the area to dry completely. Wipe the in-
stallation area with the included alcohol pad to remove any wax or polish; allow the
area to dry completely.
STEP 3 Test fit the Tri-Line Gauge Trim as shown
in PIC 2. Hold the bottom of the trim
against the fairing, then press in at the
top. Remove the Gauge Trim after you are
comfortable with test fit.
STEP 4
Use your fingernail to rub
the adhesive backing;
this will activate the ad-
hesive. Remove and dis-
card the backing.
STEP 5 Align the Trim on the
fairing. Press the bottom, top and sides into place for one minute; full bonding will
occur after 24 hours.
NOTE: If the bike is going to be operated before full bonding occurs,
secure the Trim to the fairing with a good quality masking or
painter’s tape.
INSTALLATION
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
● The product must be properly installed,
maintained and operated under
normal conditions.
● Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
● Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
● Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
● Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
● Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with your
address to: Küryakyn
454 County Road V V
Somerset, WI 54025-9031
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
TRI-LINE GAUGE TRIM
7284-21HD-0414
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality or damage the product itself
or the product to which it is being attached.
7284
Ride On!
Ensure proper adhesion of this product. Clean the installation
area of grease, oil, bugs, dirt and other debris (including wax
and polish). Küryakyn WILL NOT issue a warranty for any im-
properly installed products.
Do not attempt this installation in temperatures below 50° F.
Proper adhesive bonding ONLY occurs above 50° F.
PIC 1
PIC 2
ALIGN BOTTOM
PRESS TOP INWARD
CLEAN + DRY