Kuryakyn 5021 SUPER lizard maximus kit - Manual

CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold
hereunder, shall be free of defects in materials and
workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the
following provisions:
• Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt showing
the date the customer purchased the product(s).
• The product must be properly installed,
maintained and operated under normal conditions.
• Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated products.
• Küryakyn shall not be liable for any consequential
and incidental damages, including labor and
paint, resulting from failure of a Küryakyn product,
failure to deliver, delay in delivery, delivery in non-
conforming condition, or for any breech of contract
or duty between Küryakyn and a customer.
• Küryakyn products are often intended for use
in specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
• Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the con-
sumer. Components of Küryakyn products containing
L.E.D.s will be warranted for defects in materials and
workmanship for 3 years from the date of purchase.
• Küryakyn makes no warranty of any kind in
regard to other manufacturer’s products distributed
by Küryakyn. Küryakyn will pass on all warranties
made by the manufacturer and where possible, will
expedite the claim on behalf of the customer,
but ultimately, responsibility for disposition of the
warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
You’ll find all our innovations for H-D, GL and
Metric Cruisers in our annual catalogs. Order online
today–select the ”CATALOGS” icon. Each Küryakyn
product comes with a Proof-of-Purchase good for a
complimentary catalog. Details in packaging.
Be sure to ask your local dealer about other
Küryakyn products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA All Rights reserved.
I N S TA L L AT I O N
PARTS INCLUDED
8 Single Seven Color Lizard Light
4 “Y” Lizard Light Connector
4 Double Male Lizard Light Connector
6 Double Female Lizard Light Connector
6 9” Extension Wire
2 12” Extension Wire
2 18” Extension Wire
8 Adhesive Pad for Lizard Light
1 Lizard Light Control Switch
6 Alcohol Pad
2 Dielectric Grease
6 4” Cable Ties
4 Adhesive Foam Pads
1 Installation Instructions
Please read and understand entire instructions before starting installation.
ThANk YOU fOR ChOOSING kURYAkYN!
LIGhT PLACEMENT
This kit is designed with the correct components to illuminate the engine compartment
in the frame. If you wish to have lights outside of this area (rear swing arm, front wheel
etc.) you will need to purchase additional wiring components.
NOTE
This kit comes with 8 Lizard Lights. You can operate the Infinity Streamliner (equals 4
Lizard lights), and the Infinity Timing Cover (equals 3 Lizard lights), with this kit using
just one control switch.
CAUTIONS
1 Do not operate more than 16 Seven Color Lizard Lights on one controller.
2 Seven Color Lizard Lights are designed for display or parade use. Check local
regulations regarding the use and placement of colored lights when the vehicle is
operated on public streets.
3 To prevent corrosion, apply dielectric grease to all connections (including plugs).
4 Do not affix Seven Color Lizard Lights to hot engine or exhaust components.
5 The mounting surface must be perfectly clean for Lizard Lights to properly adhere.
Remove wax, dirt, dust, or any oily film with the alcohol pads provided before
application.
PROCEDURE
STEP 1 Use your imagination! Determine what areas or features of the bike you wish
to highlight. Mark your desired locations with small pieces of masking tape. This will
allow you to determine if the supplied leads will be suitable for your plan. If you have
a bike with a rubber mounted engine, keep engine movement in mind. Do not mount
Lizard Lights where the engine or any related components might contact the lights or
wiring during normal operation. Try to place plug connections in locations that will ease
removal of the motorcycle’s components as needed (i.e. fuel tank, horn). This will ease
future service procedures.
-cont.-
5021-11hD-1108
S U P E R L I z A R D M A x I M U S k I T 5 0 2 1