Kuryakyn 8845 rear peg ADAPTERS - Manual

I N S T A L L A T I O N
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold
hereunder, shall be free of defects in materials and
workmanship for a period of one (1) year from the
date of purchase by the consumer excepting the
following provisions:
• Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt showing
the date the customer purchased the product(s).
• The product must be properly installed,
maintained and operated under normal conditions.
• Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated products.
• Küryakyn shall not be liable for any consequential
and incidental damages, including labor and
paint, resulting from failure of a Küryakyn product,
failure to deliver, delay in delivery, delivery in
nonconforming condition, or for any breech of
contract or duty between Küryakyn and a customer.
• Küryakyn products are often intended for use
in specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
• Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the con-
sumer. Components of Küryakyn products containing
L.E.D.s will be warranted for defects in materials and
workmanship for 3 years from the date of purchase.
• Küryakyn makes no warranty of any kind in
regard to other manufacturer’s products distributed
by Küryakyn. Küryakyn will pass on all warranties
made by the manufacturer and where possible, will
expedite the claim on behalf of the customer,
but ultimately, responsibility for disposition of the
warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
You’ll find all our innovations for H-D, GL and
Metric Cruisers in our annual catalogs. Order
online today–select the ”CATALOGS” icon. Each
Küryakyn ® product comes with a Proof-of-Purchase
good for a complimentary catalog.
Details in packaging.
Be sure to ask your local dealer about other
Küryakyn ® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA ® All Rights reserved.
PARTS INCLUDED
1 Right Rear Peg Adapter
1 Left Rear Peg Adapter
1 Hardware Kit, Including:
2 10-32 X 1/2” Setscrews
1 Installation Instructions
Please read and understand entire instructions before starting installation.
ThANk YOU fOR ChOOSING küRYAkYN!
IN ORDER TO PROTECT YOU AND OThERS fROM POSSIBLE INjURY
AND/OR PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION
TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES
REGARDING ThE USE AND CARE Of ThIS PRODUCT.
CAUTION! This indication alerts you to the fact that ignoring the contents described herein
can result in potential injury or material damage.
ATTENTION! This indication alerts you to the fact that ignoring the contents described herein
may negatively affect product performance and functionality.
TOOLS SUGGESTED
Set of hex wrenches and a set of combination wrenches.
STRICTLY OBSERVE ThE fOLLOWING GUIDELINES IN ORDER TO USE ThE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
PROCEDURE
STEP 1 Read and understand all steps in the instructions before starting the installation.
Park the motorcycle on a hard, level surface and turn off the ignition.
CAUTION! Larger footpegs may limit cornering clearance.
STEP 2 Remove the stock rear foot pegs and set aside all mounting hardware (make note
in the order of ball detent and washer(s) location). They will be reused with new
application.
STEP 3 Insert setscrew on the backside of the new peg adapter for adjustment later.
STEP 4 Mount new peg adapter using the stock hardware and supplied cotter pin.
STEP 5 Check to see if the new adapter locks in the upward position and releases easily.
If it is not locking, disassemble and check to see if ball detent is pushed out of the
adapter far enough to grab the locking washer. Reassemble after inspection.
STEP 6 Tighten all fasteners and repeat on opposite side.
STEP 7 The setscrew can be turned in or turned out to set the height of the peg.
ATTENTION! It is the installer’s responsibility to ensure that all of the fasteners
(including pre-assembled) are tightened before operation of the motorcycle.
Küryakyn will not warranty components lost due to improper installation.
Periodic maintenance may be required.
f O R k A W A S A k I
fITS: kAWASAkI: ZX6R ’00 & UP, ZX7R ’00 - ’03, ZX9R ’02 & ’03, ZX10R ’04 & UP,
ZX11R ’00 & ’01, ZX12R ’00 - ’05, ZX14R ’06 & UP
8845-11MC-0908
R E A R P E G A D A P T E R 8 8 4 5