Kuryakyn 4217 ANTENNA FLAG HOLDER User Manual

Ride on, Installation, Antenna flag holder 4217

Advertising
background image

INSTALLATION

CUSTOMER SERVICE

877.370.3604 (toll free)

INSTALLATION QUESTIONS

[email protected]

or call 715.247.2983

LIMITED WARRANTY

Küryakyn warrants that any Küryakyn products

sold hereunder, shall be free of defects in

materials and workmanship for a period of one

(1) year from the date of purchase by the

consumer excepting the following provisions:

Küryakyn shall have no obligation in the event

the customer is unable to provide a receipt

showing the date the customer purchased the

product(s).

The product must be properly installed,

maintained and operated under

normal conditions.

Küryakyn makes no warranty, expressed or

implied, with respect to any gold plated

products.

Küryakyn shall not be liable for any

consequential and incidental damages, including

labor and paint, resulting from failure of a

Küryakyn product, failure to deliver, delay in

delivery, delivery in nonconforming condition, or

for any breech of contract or duty between

Küryakyn and a customer.

Küryakyn products are often intended for use in

specific applications. Küryakyn makes no

warranty if a Küryakyn product is used in

applications other than intended.

Küryakyn electrical products are warranted for

one (1) year from the date of purchase by the

consumer. L.E.D.’S contained in components of

Küryakyn products will be warranted for defects

in materials and workmanship for 3 years from

the date of purchase where as all other

components shall be warranted for one(1) year.

This includes, but is not limited to; control

modules, wiring, chrome & other components.

Küryakyn makes no warranty of any kind in

regard to other manufacturer¹s products

distributed by Küryakyn. Küryakyn will pass on

all warranties made by the manufacturer and

where possible, will expedite the claim on behalf

of the customer, but ultimately, responsibility for

disposition of the warranty claim lies

with the manufacturer.

ABOUT OUR CATALOG

For purchasing Küryakyn® products, you

can receive a complete catalog free of charge.

Send the Proof-of-Purchase below with

your address to: Küryakyn, P.O. Box 339,

Somerset, WI 54025.

Please indicate either Accessories Catalog for

Harley-Davidson® or GL & Metric Cruisers.

Be sure to ask your local dealer about other

Küryakyn® products, the motorcycle parts and

accessories designed for riders by riders.

©2005 Küryakyn USA® All Rights reserved.

PARTS INCLUDED

1

Outside Tube

1

Inside Tube

2

Rubber Stop

1

White Flag

1

American Flag

1

Installation Instructions

Please read and understand entire instructions before starting installation.

THANK YOU FOR CHOOSING K

ϋ

RYAKYN!

IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.


TOOLS SUGGESTED

Liquid Hand Soap

STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.

STEP 1

Read and understand all steps in the instructions before starting the

installation. Park the motorcycle on a hard, level surface and turn off the

ignition.


STEP 2

Using your liquid hand soap, lubricate the hole in the Rubber Stop so the tip of

the antenna can easily slide through the Rubber Stop..


STEP 3

Slide the Inside Tube (smaller tube) in place on the antenna with the large end

down. See PIC.1.


STEP 4

Slip the flag over the antenna and over the Inside Tube. See PIC.2.


STEP 5

Compress the flag down to allow room

to slide the Outside Tube (with the

large end up) onto the Inside Tube

locking the two tubes together.

Once the Inner and outer tubes are

started together, feed the flag up over

the tubes. Slide the tubes together

until the ends match up and the flag is

in place. See PIC.3.


STEP 6

Slide the Rubber Stop up against the

locked Inside and Outside tubes and

the installation is complete. See PIC.4.


STEP 7

For a lower position on the antenna,

place the second rubber stop above

the tube and flag assembly and slide

down to the desired position.

ANTENNA FLAG HOLDER

4217

4217-21HD-0911

PIC 1

PIC 2

PIC 3

PIC 4

Ride On!

Advertising