Brill 33 EF - Manual (Page 21)

GB
F
21
Do not start the motor when
you are standing in front of the
discharge duct.
Keep your fingers and feet away
from the cutting tool!
Never lift or carry a machine with
the motor running.
Each time you have to work on the
machine or leave it or top it up,
always switch off the motor.
If you strike an obstacle when
working, please disable the
machine. Unplug from the mains.
Remove the obstacle, check the
equipment for any damage and
have it repaired if necessary.
If the equipment begins to vibrate
strongly, unplug from the mains
and ascertain the cause.
A
Taking
a Break
Never leave the equipment unat-
tended. If you stop work, unplug
the equipment from the mains and
store the equipment in a safe place.
If you stop work to go to a dif-
ferent work area, it is essential
to turn the equipment off and
unplug from the mains.
A
Beware of Environmental
Influences
Never use the equipment in the
rain or in damp, wet conditions.
Never work immediately adjacent
to a swimming pool or garden
pond with electrical equipment.
Comply with local quiet periods in
your community!
A
Electrical
safety
Check the power cable regularly
for damage and signs of wear.
Only use permitted extension
cables.
Unplug the mains plug immediately
if the mains cable / extension cable
is damaged or severed.
The manufacturer warrants its
products for exclusively non-com-
mercial use for a period of
24 months from the date of origi-
nal purchase. This warranty does
not affect statutory warranty claims.
The warranty covers all substantial
faults of the product, which are
caused by defects in material and
workmanship. If a product exhibits
such a defect we will, at our option,
repair or replace it without cost for
parts and labour provided the fol-
lowing requirements are fulfilled:
.
The product must have been
sold to the customer in a legally
correct way.
.
The original receipt with the cus-
tomer’s address, date of pur-
chase, model and product desig-
nation is presented as proof of
purchase. The product must have
been purchased within the EC.
.
The product was handled proper-
ly and according to the recom-
mendations in the operating
instructions. It is essential that the
product has been maintained
and cleaned according to the
information in the operating
instructions. No attempt to disas-
semble or repair the product has
been made by either the buyer
or an unauthorised third party.
.
It must be ensured that only origi-
nal replacement parts and origi-
nal accessories approved by the
manufacturer are used. There may
be an increased risk of conse-
quential damage and accidents if
non-original parts or non-original
accessories are used. This war-
ranty does not cover consequen-
tial damages.
.
The product must be either taken
directly or sent with postage paid
to an authorised service centre.
The original receipt must be sent
with the product.
.
The warranty does not cover
damage from misuse, abuse, use
of unsuitable, non-original or
unauthorised interchangeable
parts, replacement parts or
accessories, as well as improper
maintenance and cleaning.
The products contain various com-
ponents that are subject to normal
or use-related wear. The warranty
does not extend to these wearing
parts.
In particular the following compo-
nents relating to this product are
excluded:
Blades / blade bar / drive belt /
care roller / blade roller /
lower blade / cutting plate /
cutting line / cutting head cover /
saw blade / nickel-cadmium-cell
(battery).
The manufacturer warranty
does not affect existing warranty
claims between the customer
and the dealer / seller.
Warranty
Veuillez lire attentivement ce mode
d’emploi, respecter les informations et les consignes de sécurité fournies.
Familiarisez-vous avec l’appareil, ses éléments de réglage et son em-
ploi correct à l'aide de ce manuel.
4. Informations sur le mode d’emploi