Bulova ALL-PRO EI700NB - Manual

Watch Setting Guide
FEATURES
1. Hours minutes and seconds display.
2. Chronograph (CHRONO) with minutes, seconds and 1/10 second
display. Maximum reading is 30 minutes.
3. Split time chronograph function.
4. Date display.
5.Time zone adjustment
Note: The Second hand for the time display is the small hand in the
bottom dial.
A. SETTING THE TIME
1. Pull the crown out to position “3” (See diagram). If the crown has a
“screw-down” lock, then unscrew the crown lock first by turning the
crown toward you, then pull it to position “3”.
2.Turn the crown away from you (hands moves clockwise), until the date
changes (midnight).
3. Continue turning the hour and minute hands to the correct time.
If it is afternoon you must go past 12 o’clock again (noon) to set the
correct time.
4.When the correct time is set, push crown back to position “1”.
B. SETTING THE TIME ZONE AND THE DATE
1. Pull the crown to position “2” (See diagram).The watch will continue to
run.Turn the crown in either direction and the Hour Hand will jump
either forwards or backwards one hour at a time.This is for Time Zone
correction – Only the hour hand moves.
2. For date setting, simply continue moving the hour hand (forwards or
backwards) until the date changes at midnight. Repeat this until the
correct date appears.
Don’t forget – the date changes at midnight – When moving the hour
hand forward go past 12 o’clock noon again if you are setting to PM
time. If you are setting the hand backward go back 12 more hours after
the date is set to get to AM time.
Note: Go in the direction closest to the actual date. For example: If you
start at the date “22”, and you wish to set the date to “20”, then move
the hour hand backwards (Counter-clockwise). If you start at “22”, and
the actual date is “25”, then move the Hour Hand forward (clockwise).
3. Once the date is set, push the crown back to position “1”.
C. CHRONOGRAPH (CHRONO) ADJUSTMENT
This must be done before using the chrono the first time. It does not
need to be repeated unless the watch receives an impact sufficient to move
the hand out of position, or the Battery has been changed.
Note: When using the buttons for these adjustments, each button push
will move the hand one step – B ut holding the button down will advance
the hand rapidly.
1. Pull crown out to position “3”.
2. Push button “A” to move the Chrono second hand (long hand) to the
“0” or 12 o’clock position.
2. Push button “B” to move the 1/10 second hand (small dial at 2 o’clock)
to the “0’ position.
3. Move crown to position “2”. Push button “B” to move the 30 minute
chrono hand (small dial at 10 o’clock) to the “0” or 12 o’clock position.
4. Push crown back to position “1”.
D. USING THE CHRONOGRAPH (CHRONO)
Note: The maximum chrono reading is 30 minutes, However the chrono
will continue running once 30 minutes has passed.The resulting half hour
periods may be added together mentally to keep track of longer periods.
For example – If you know that approximately one hour has passed since
you started the chronograph, and the chrono reads 25 minutes, then you
know that the chrono has been running 30 minutes plus 25 minutes, which
is 55 minutes.
1. Push Button “A” to start the chronograph. Push button “A” again to stop
the chronograph.
(Note: the 1/10 second hand does not move until the chrono is
stopped.Then it shows the elapsed 1/10 seconds).
2. Push button “B” to return the chronograph to the “Zero” or starting
point.
3. Chronograph can be stopped and started again (Button “A”), repeatedly,
to “ADD” times together.
4.To “split” times, with the chrono running, push button “B”. Chrono
hands will stop.Then push "B” again and the hands will catch up to actual
elapsed time and continue running.
Technical
Letter
BOOK NO. 556 ACCUTRON CHRONO
4/2002