Omnitron Systems Technology iConverter GX/TM2 Plugin Module - Manual (Page 2)

Port of the GX/TM2 is isolated from the
chassis’ Ethernet Backplane. When this
DIP-switch is in the RIGHT “EN” position,
the Backplane Port is enabled. This
allows Ethernet Backplane connectivity
to an adjacent module via the chassis
Backplane Link “A” or “B” depending on
the switch setting.
Sw3 - MASTER/SlAVE
When the GX/TM2 module is installed in a chassis with an iConverter management
module such as a 10/100M2, set the DIP-switch to the LEFT “M/SL” position (factory
default), the assignment of mastership is automatically negotiated by the installed
management modules. To designate the GX/TM2 module as the master of the chassis,
set the DIP-switch on the module to the LEFT “M/SL” position, and set the DIP-switch
on the other installed management modules to the RIGHT “SL” position to enable
Slave-Only mode.
Sw4 - RESERVED
This DIP-switch is for factory use only and must always remain in the LEFT position
(factory default).
2) InSTAll MoDUlE In ChASSIS AnD ConnECT CABlES
a. Carefully slide the module into an open slot in the chassis. Align the module with
the installation guides and ensure that the module is firmly seated against the
backplane. Secure the module by fastening the front panel thumbscrew (push in and
turn clockwise to tighten) to the chassis front. Verify the “Pwr” LED is ON (indicating
the chassis is powered).
b. When using a GX/TM2 SFP model (8939N-0), insert the SFP Fiber transceiver into
the Port 1 SFP receptacle on the GX/TM2.
NOTE: The release latch of the SFP Fiber transceiver must be in the closed
position before insertion.
c. Connect an appropriate multimode or single-mode fiber cable to the fiber port of the
installed module. It is important to ensure that the transmit (Tx) is attached to the
receive side of the device at the other end and the receive (Rx) is attached to the
transmit side. Single-fiber (SF) media converter models operate in pairs. The Tx
wavelength must match the Rx wavelength at the other end and the Rx wavelength
must match the Tx wavelength at the other end
d. Connect the UTP port via a Category 5 cable to a 10BASE-T, 100BASE-TX or
1000BASE-T Ethernet device.
3) ConFIGURE MoDUlE VIA CoMMAnD lInE InTERFACE
To access the Command Line Interface (CLI), connect the GX/TM2 RS-232 Console
Port to the COM port of a computer equipped with terminal emulation software such
as HyperTerminal. The Console Port (DCE) is a mini DIN-6 female connector which
can be changed to a DB-9 connector with the included adapter. The GX/TM2 Console
Port is a standard asynchronous serial interface.
Start HyperTerminal and select the correct COM Port in the HyperTerminal “Connect
To:” window. Set the serial port to the following:
Bits Per Second
57,600 Parity NONE
Stop Bits 1 Hardware Flow Control NONE
Data Bits 8
Switch
Left
(Factory Default)
Right
Sw1
An:
Fiber Auto-Negotiation
Man:
Fiber Manual Negotiation
Sw2
An:
UTP Auto-Negotiation
Man:
UTP Manual
Sw3
1000:
UTP 1000Mbps
10-100:
UTP 10-100Mbps
Sw4
100:
UTP 100Mbps
10:
UTP 10Mbps
Sw5
FDX:
UTP Full-Duplex
hDX:
UTP Half-Duplex
Sw6
See Link Mode Selection Sw7
Sw8
Sw6 Sw7 Sw8 Link Mode Selection
Left Left Left
Link Segment (LS)
(Factory Default)
Right Left Left Link Propagate (LP)
Left Right Left
Remote Fault Detect + Link
Segment (RFD + LS)
Right Right Left
Remote Fault Detect + Link
Propagate (RFD + LP)
Left Left Right Symmetrical Fault Detect (SFD)
Right Left Right
Asymmetrical Link Propagate
Port 1 to Port 2 (ALP P1-P2)
Left Right Right
Asymmetrical Link Propagate
Port 2 to Port 1 (ALP P2-P1)
Right Right Right Pass Remote Link Fault (PRLF)
Figure B: DIP-Switch Bank 1
Sw2 Sw3 Sw4 Sw5 Function
AN 1000 100 or 10 FDX
The UTP port is set to auto-negotiation with the following modes advertised:
1000F, 1000H, 100F, 100H, 10F, 10H
AN 1000 100 or 10 HDX
The UTP port is set to auto-negotiation with the following modes advertised:
1000H, 100F, 100H, 10F, 10H
AN 10-100 100 FDX
The UTP port is set to auto-negotiation with the following modes advertised:
100F, 100H, 10F, 10H
AN 10-100 100 HDX
The UTP port is set to auto-negotiation with the following modes advertised:
100H, 10F, 10H
AN 10-100 10 FDX
The UTP port is set to auto-negotiation with the following modes advertised:
10F, 10H
AN 10-100 10 HDX
The UTP port is set to auto-negotiation with the following modes advertised:
10H
MAN 1000 100 or 10 FDX
The UTP port is set to auto-negotiation with the following modes advertised:
1000F, 1000H, 100F, 100H, 10F, 10H
MAN 1000 100 or 10 HDX
The UTP port is set to auto-negotiation with the following modes advertised:
1000H, 100F, 100H, 10F, 10H
MAN 10-100 100 FDX
The UTP port is set to manual negotiation and is forced to:
100F
MAN 10-100 100 HDX
The UTP port is set to manual negotiation and is forced to:
100H
MAN 10-100 10 FDX
The UTP port is set to manual negotiation and is forced to:
10F
MAN 10-100 10 HDX
The UTP port is set to manual negotiation and is forced to:
10H
Figure C: UTP Configuration Matrix
Sw6, Sw7, Sw8 - lInK MoDES
These three DIP-switches configure the link mode settings. It is recommended to have
link modes DOWN (default) during the initial installation. After the circuit has been tested
and operational, configure the module for the desire mode. For detailed information on
the operation of the different Link Modes, download the application note “ iConverter
Link Modes” available on Omnitron’s web site.
DIP-SwITCh BAnK 2
Sw1, Sw2 - BACKPlAnE EnABlE
When the DIP-switch is in the LEFT “DS” position (factory default), the Backplane
Switch Left (Factory Default) Right
Sw1 A-DS: Port A Disabled A-En: Port A Enabled
Sw2 B-DS: Port B Disabled B-En: Port B Enabled
Sw3 M/Sl:
Master/Slave Auto-Select
Sl:
Slave-Mode Only
Sw4 Reserved Reserved
Figure D: DIP-Switch Bank 2
Page 2 Page 3