Prescolite D2ICAT User Manual

Instruction sheet, Sh ee t, Instr uction

Advertising

Instr
uction

Part No...........................................

With representatives offices in principal cities throughout North America.

701 Millennium Blvd., Greenville, SC 29607

olit

e.c

olit

Tol

l Fr

ical

por

1.888
.P

S.4T

ours:

- 5p

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information

and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,

and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and

during servicing or relamping, turn off power at fuse or circuit breaker.

All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.

Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in

compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by

the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from

product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or

the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

93040526

2012 01/25/12

WARNING – This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash your hands after installing, handling, cleaning, or otherwise touching this product.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

KEEP THESE INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

MODEL D2ICAT

NTE

R L

INE

CENT

ER LI

The bar hanger brackets are shipped flat. Bend the tabs on
the brackets as show n to allow the use of accessory m ounting
channels or bar hangers (Prescolite B6, B24, or by others).
M ount the fram e in the ceiling so that the w eight of the
assem bly is safely supported by the m ounting channel or bar
and/or hanger w ires secured to the building structure.

Rem ove the top of the housing and adjust the fram e so the
bottom surface is flush w ith the ceiling m aterial m ounting
surface (backside of the ceiling m aterial) and in alignm ent
w ith adjacent fixtures. The rivets for the 8” x 8”
polycarbonate cut-through panel m ay be used as centerlines
(as show n) for aligning the fram e. Secure the m ounting
brackets by tightening w ing nuts on either side of the fram e
inside the D2IC A T housing.

Important! When the ceiling material is added
(covering the D2ICAT) make sure the D2ICAT is
flush with the back side of the ceiling material and
solidly mounted. Mark the fixture installation
location accurately so the hole cut-through location
will be accurate!

There are four 3/8” M C flexible conduit entry points located
on the rear cover plate of the D2IC A T to allow the
UNENERGIZED line voltage and control (0-10V dim m ing)
flexible conduit to be inserted into the housing until they are
used w hen the D2LED fixture is w ired and installed. There are
four conduit gaskets included w ith the D2IC A T housing to be
used if needed to seal the conduit opening further after the
flexible conduit is installed. There is also a tether cable
m ounted inside the housing to be attached to the D2LED
fixture in the case of seism ic conditions at the install location.
This tether, if needed, should be attached to the screw on the
light engine (see Figure A ) after the w iring is com plete and
the J-tube is inserted in the ceiling, but before fixture is
installed.

Install the D2LED fixture per the instruction sheet provided w ith
the fixture. W hen the hole is cut in the ceiling w ith the 2-7/8”
hole saw (by others), it w ill cut through the ceiling m aterial
and the D2IC A T polycarbonate cut-through panel at the sam e
tim e providing accurate alignm ent in both the ceiling m aterial
and the D2IC A T.

WARNING: DO NOT pinch wires between J-tube
cover and J-tube endplates. Consult a Qualified
Electrician for all other options that require other
wiring configurations.

DETAIL A

D2ICAT WITH D2LED INSTALLED

8" x 8"

Polycarbonate

Panel

Cut-Through

Area

Siesmic

Tether

D2LED

Fixture Screw

3/8" Flexible

Conduit

Entry Points

Extra

Conduit

Gaskets

Instruction

Sheet

www.prescolite.com

•

Prescolite

TollFree

Technical

Support

1.888.PRS.4TEC

•

Hours:

8am

- 5pm

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93040526

Instruction

Sheet

INSTALLATION INSTRUCTIONS

MODEL D2ICAT

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and

instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and

proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during

servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other poten-

tial hazard. Product must be mounted in locations and at heights and in a manner consistent with its

intended use, and in compliance with the National Electrical Code and local codes. The use of accessory

equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do

not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such

as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may

cause an unsafe condition.

WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

KEEP THESE INSTALLATION INSTRUCTIONS

1. The bar hanger brackets are shipped flat. Bend the tabs on the

brackets as shown to allow the use of accessory mounting channels

or bar hangers (Prescolite B6, B24, or by others). Mount the frame

in the ceiling so that the weight of the assembly is safely supported

by the mounting channel or bar and/or hanger wires secured to

the building structure.

2. Remove the top of the housing and adjust the frame so the bottom

surface is flush with the ceiling material mounting surface (backside

of the ceiling material) and in alignment with adjacent fixtures.

The rivets for the 8” x 8” polycarbonate cut-through panel may be

used as centerlines (as shown) for aligning the frame. Secure the

mounting brackets by tightening wing nuts on either side of the

frame inside the D2ICAT housing.

3. Important! When the ceiling material is added (covering

the D2ICAT) make sure the D2ICAT is flush with the

back side of the ceiling material and solidly mounted.

Mark the fixture installation location accurately so the

hole cut-through location will be accurate!

4. There are four 3/8” MC flexible conduit entry points located on the

rear cover plate of the D2ICAT to allow the UNENERGIZED line

voltage and control (0-10V dimming) flexible conduit to be inserted

into the housing until they are used when the D2LED fixture is wired

and installed. There are four conduit gaskets included with the

D2ICAT housing to be used if needed to seal the conduit opening

further after the flexible conduit is installed. There is also a tether

cable mounted inside the housing to be attached to the D2LED

fixture in the case of seismic conditions at the install location. This

tether, if needed, should be attached to the screw on the light

engine (see Detail A) after the wiring is complete and the J-tube is

inserted in the ceiling, but before fixture is installed.

5. Install the D2LED fixture per the instruction sheet provided with

the fixture. When the hole is cut in the ceiling with the 2-7/8”

hole saw (by others), it will cut through the ceiling material and

the D2ICAT polycarbonate cut-through panel at the same time

providing accurate alignment in both the ceiling material and the

D2ICAT.

6. WARNING: DO NOT pinch wires between J-tube cover

and J-tube endplates. Consult a Qualified Electrician

for all other options that require other wiring

configurations.

Seismic

Advertising

Popular Brands

Popular manuals