Prescolite AKTSLED User Manual
Instruction sheet, Sh ee t, Instr uction
Instruction
Sheet
www.prescolite.com
•
Prescolite
TollFree
Technical
Support
1.888.PRS.4TEC
•
Hours:
8am
-
5pm
ET
701 Millennium Boulevard • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2010, 03/11/10 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93027792
Instruction
Sheet
INSTALLATION INSTRUCTIONS FOR AKTSLED ON
PRESCOLITE ARCHITRAK
®
AKT SERIES TRACK
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, MAKE CERTAIN THAT
THE POWER IS OFF BEFORE INSTALLING OR SERVICING THIS FIXTURE. FOR TWO CIRCUIT
TRACK INSTALLATIONS, MAKE CERTAIN THAT BOTH CIRCUITS ARE DE-ENERGIZED.
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects and/
or other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise
touching this product.
1. Line up the track adapter with the slot in the ArchiTrak
®
AKT Series track and insert the adapter
into the slot.
2. After the adapter is inserted fully into the track, pull down on the spring locking tab.
3. Holding the spring locking tab down, rotate the fixture ¼ turn (90°) clockwise (looking up at the
track) until the locking tab is over the slot in the track. Release the locking tab and make sure the
tab is fully locked into the track slot, and that the fixture cannot rotate.
4. To remove the fixture from the track, pull the spring locking tab down and rotate the fixture ¼ turn
(90°) counter-clockwise. The fixture will release from the track.
NOTE - If the track is wired for single-circuit operation, the fixture may not light if connected to the
unwired circuit side. Remove the fixture, rotate it ½ turn (180º), and reinstall it in the track following
the same procedure as above. This will engage the wired circuit on the opposite side of the track.
If the track is wired for two circuits, removing the fixture and rotating it ½ turn (180º), and then
reinstalling it will engage the second circuit.
INSTALLATION INSTRUCTIONS FOR AKTSLED ON
PRESCOLITE ARCHITRAK
®
AKT SERIES TRACK
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, MAKE CERTAIN THAT
THE POWER IS OFF BEFORE INSTALLING OR SERVICING THIS FIXTURE. FOR TWO CIRCUIT
TRACK INSTALLATIONS, MAKE CERTAIN THAT BOTH CIRCUITS ARE DE-ENERGIZED.
1. Line up the track adapter with the slot in the ArchiTrak
®
AKT Series track and insert the adapter
into the slot.
2. After the adapter is inserted fully into the track, pull down on the spring locking tab.
3. Holding the spring locking tab down, rotate the fixture ¼ turn (90°) clockwise (looking up at the
track) until the locking tab is over the slot in the track. Release the locking tab and make sure the
tab is fully locked into the track slot, and that the fixture cannot rotate.
4. To remove the fixture from the track, pull the spring locking tab down and rotate the fixture ¼ turn
(90°) counter-clockwise. The fixture will release from the track.
NOTE - If the track is wired for single-circuit operation, the fixture may not light if connected to the
unwired circuit side. Remove the fixture, rotate it ½ turn (180º), and reinstall it in the track following
the same procedure as above. This will engage the wired circuit on the opposite side of the track.
If the track is wired for two circuits, removing the fixture and rotating it ½ turn (180º), and then
reinstalling it will engage the second circuit.
1 INSERT ADAPTER
2
PULL LOCKING TAB DOWN
3 ROTATE 90º CLOCKWISE
PRESCOLITE ARCHITRAK
AKT SERIES TRACK
Sh
ee
t
Part No...........................................
With representatives offices in principal cities throughout North America.
Copyright , revision, All Rights Reserved - Printed in U.S.A.
701 Millennium Blvd., Greenville, SC 29607
w
w
w
.p
re
sc
olit
e.c
om
y
Pre
sc
olit
e T
oll
Fre
e T
ec
hn
ica
l S
up
po
rt
1.8
88
.P
R
S.4
TE
C
y
H
ou
rs:
8
am
- 5
pm
E
T
y
M
-F
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker.
All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
93027792
2010 03/10/10
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects and/or
other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise
touching this product.
Instr
uction
KEEP THESE INSTALLATION INSTRUCTIONS
KEEP THESE INSTALLATION INSTRUCTIONS