Prescolite CFT857HEB - Manual

Instruction
Sheet
www
.prescolite.com
• Prescolite
TollFree
Technical Support
1.888.PRS.4TEC
• Hours: 8am - 5pm ET
101 Corporate Drive • Spartanburg, SC 29303
With representatives offices in principal cities throughout North America.
Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157940100
Instruction
Sheet
INSTALLATION INSTRUCTIONS
CFT857HEB HOUSING & REFLECTORS
Reflector
Socket Mounting
Bracket
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND PROPER
OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
1. Bend brackets as shown in Detail “A”.
Install the fixture in the ceiling using
mounting channel or bar (by others)
placed in the adjustable mounting
brackets. Mount the fixture in the ceiling
so that the weight of the fixture is
supported by the mounting channel or bar
and/or hanger wires secured to the
building structure.
Note: Housing orientation for wall wash
applications.
2. Adjust the fixture so the bottom of the
plaster flange is flush with the finished
ceiling line and in alignment with adjacent
fixtures. Secure mounting brackets by
tightening wing nut on either side of the
fixture.
3. Determine where the supply wiring conduit
will enter the J-Box and attach it in con
formance with the National Electric Code.
4. Remove J-Box cover plate. Remove
appropriate knockout and assemble
appropriate connector for the supply wire
used. Connect ground wires to green
ground leads. Connect white (common) to
white (leads). Connect power supply (line)
to black lead(s). Reinstall J-Box cover.
WARNING: DO NOT pinch wires
between J-Box/ballast cover and J-Box.
Consult a Qualified Electrician for all
other options that require other wiring
configurations.
5. Reflector Installation: After all ceiling
installation and finishing work is complete.
Place the reflector in the plaster flange
aperture, insert the stud on the socket
mounting bracket through the center hole
in the top of the reflector. Push the
reflector up until the flange on the reflector
is flush against the finished ceiling and
tighten the wing nut.
Note: Orientation of reflector for wall
wash application.
6. Install the proper lamps (by others).
Wing Nut (2)
Kicker Goes Away From
Wall When Using Wall
Wash Reflector
Brackets are
supplied flat.
Bend brackets in
line with marks
on flange.
This end
towards wall
for wall wash
application DETAIL “A”
Ballast
Adjustable
Mounting
Bracket (2)
Plaster
Frame
Wing Nut
(Supplied W/ HSG)
J-Box/Ballast
Covers
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.