Prescolite CFT942HEB 347V (42W) - Manual

Ins
tru
ctio
nS
he
et
w
w
w
.p
re
sc
olit
e.c
om
• P
res
co
lite
To
llF
ree
Te
ch
nic
al S
up
po
rt
1.8
88
.P
RS
.4T
EC
•
H
ou
rs:
8a
m
- 5
pm
E
T
701 Millennium Boulevard • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2009, 10/29/09 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135250100
Ins
tru
ctio
nS
he
et
INSTALLATION INSTRUCTIONS
CFT932HEB/EBDM (26-42W),CFT932HEB 347V (26-32W)
CFT942HEB 347V (42W)
Step 7
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND PROPER
OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
1. If reflector-holding-bridge is folded,
rotate to upright position. Secure by
tightening bridge fasteners (screws,
wing screws, or wing nuts).
2. Bend mounting brackets as shown.
Install the fixture in the ceiling using
Prescolite B24 or bar stock, 1/2" inch
EMT, or C-channels (by others) placed
through the adjustable mounting brack-
ets. Mount the fixture in the ceiling so
that the weight of the fixture is support-
ed by the mounting channel or bar
and/or hanger wires secured to the
building structure. Note: orientation for
wall wash applications.
3. Adjust the fixture so the bottomof the
plaster flange is flush with the ceiling
line and in alignment with adjacent
fixtures. Secure mounting brackets by
tightening adjustment wing nuts on both
sides of the fixture.
Wing Nut
4. Remove J-Box cover plate. Remove
appropriate knockout and assemble
appropriate connector for the supply
wire used. Connect ground wires to
green ground leads. Connect white
(common) to white (leads). Connect
power supply (line) to black lead(s).
Reinstall J-Box cover.WARNING:
DO NOT pinch wires between
J-Box/ballast cover and J-Box.
Consult a Qualified Electrician
for all other options that require
other wiring configurations.
5. Install reflector after all ceiling
installtion and finishing work is
complete. insert socket mounting
bracket into correct position
depending on lamp wattage.
Tighten reflector to socket-mount-
ing-bracket with 2 wing nuts.
6. Push reflector into plaster flange
until reflector is flush against
ceiling. Tighten reflector and socket
mounting bracket to reflector
holding bracket with wing nut. Note:
orientation for wall wash
applications.
7. Install the proper lamps (by others).
One Position for
all Wattages
Kicker Goes Away From Wall When
Using Wall Wash Applications
Reflector
Align Mounting Brackets
with Marks on Flange
Low Voltage Dimming Wires
(Dimming Units Only)
Reflector-
Holding-
Bridge
Bridge Fasteners
This End Towards Wall For
Wall Wash Applications
J-Box/Ballast
Cover
Step 6
Socket Mounting
Bracket
Use this Position for 42
Watt Lamp
Use this Position for 32
and 26 Watt Lamp
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other
reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.