Prescolite 6B3STAC - Manual

Instruction
Sheet
Part No........................................................930017587
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions concerning Wet or Damp
Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do not install in areas subject to combustible vapors or gases.
Before wiring to power supply and during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed
by qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard. Product must be
mounted in locations and at heights and in a manner consistent with its intended use, and in compliance with the National Electrical
Code and local building codes. The use of accessory equipment not recommended by the manufacturer or installed contrary to instructions may cause an
unsafe condition. Do not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains,
screens or the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.
INSTALLATION INSTRUCTIONS
6C3FC, 6B3FC, 6C3STFC, 6B3STFC
6C3AC, 6B3AC, 6C3STAC, 6B3STAC REFLECTOR
www
.prescolite.com
Prescolite T
ollFree T
echnical Suppor
t
1.888.PRS.4TEC
Hours: 8am - 5pm ET
A. Lamp Adjustment Prior
To Trim Installation:
1. Turn power off.
2. Loosen horizontal and vertical locking
Thumbscrews as shown, (1) & (2).
3. Remove Lamp Holder (3). Install lamp into
Socket (4). Re-install Lamp Holder into Lamp
Mounting Plate (5).
4. Rotate Lamp Adjusting Mechanism (6)
to desired vertical angle and horizontal
position by inserting a standard screwdriver
into slots as shown.(6) NOTE: Vertical
increment indicator numbers can
be used to pre-adjust the vertical
angle if desired. NOTE: Set lamp
position at 0º for FC trims, or at
specified angle shown on trim label
for AC trims. Rotate thumbscrew (2)
clockwise to lock in place.
B. Trim Installation:
1. Remove Screw (10), pull Safety Cable (7)
through opening in Plaster Frame and attach
to Trim as shown using screw (10).
2. Squeeze the two Torsion Springs (8) together
and insert ends into slots on both Brackets
(9) as shown.
3. Push Trim towards ceiling until the Torsion
Springs force the Trim against the ceiling
line.
C. Final Adjustment:
1. Make final horizontal adjustment by
holding outer flange on Trim and rotating
horizontally. NOTE: If necessary, pull
the flange away from the ceiling
slightly before rotating.
D. Locking Horizontal Aim:
NOTE: Turn power off and allow
lamp to cool if necessary.
1. Pull Trim away from ceiling, reach into
housing and rotate Thumb Screw (1)
clockwise to lock in place.
2. Push Trim back towards ceiling until seated
against ceiling.
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects and/or
other reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this
product.
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY
AND PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
701 Millenium Boulevard • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2008, 7/29/08 All Rights Reserved - Printed in U.S.A.

426&&;&
5034*0/

413*/(4
"4
4)08/





-0$"5&
53*.
'&"563&
"8":
'30.
4*%&
8*5)
4"'&5:
$"#-&





 
426&&;&
413*/(
50(&5)&3
"4

4)08/
"/%
*/4&35
*/
4-054




FC
(FULL CUT)
AC
(ANGLE CUT)