Prescolite LF8CFH1 User Manual

Instruction sheet, Installation instructions liteframe

Advertising
background image

Instruction

Sheet

www

.prescolite.com

Prescolite T

ollFree T

echnical

Support

1.888.PRS.4TEC

• Hours: 8am - 5pm ET

701 Millennium Blvd., • Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2008, 08/12 revision, All Rights Reserved - Printed in U.S.A.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161610100

Instruction

Sheet

INSTALLATION INSTRUCTIONS

LITEFRAME

®

HORIZONTAL COMPACT FLUORESCENT

LF6CFH & LF8CFH & LF8CFH1

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND PROPER

OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects, and/or other repro-

ductive harm. Thoroughly wash hands after installing, handling, ckeaning, or otherwise touching this product.

1. Disconnect hanger bars and brackets and re-

install as shown. Install the fixture in the ceiling
using hanger bars (supplied), or mounting
channel or bar (by others) placed in the
adjustable mounting brackets. Mount the fix-
ture in the ceiling so that the weight of the
fixture is supported by the hanger bars, mount-
ing channel, bar, and/or hanger wires secured
to the building structure.

2. Adjust the fixture so the bottom of the plaster

flange is flush with the finished ceiling line and
in alignment with adjacent fixtures. Secure
mounting brackets by tightening wing nuts on
either side of the fixture.

3. Determine where the supply wiring conduit

will enter the J-Box and attach it in confor-
mance with the National Electric Code.

4. Remove J-Box cover plate. Remove appropri-

ate knockout and assemble appropriate con-
nector for the supply wire used. Connect
ground wires to green ground leads. Connect
white (common) to white (leads). Connect
power supply (line) to black lead(s). Reinstall
J-Box cover.
WARNING: DO NOT pinch wires between J-
Box/ballast cover and J-Box. Consult a
qualified electrician for all other options
that require other wiring configurations.

5. Install the reflector after all ceiling installation

and finishing work is complete. Remove wing
nut from socket housing unit. Place three small
reflector holes around post and two extrusions
of the socket housing unit. If the reflector has
dissimilar lamp windows, the largest lamp win-
dow needs to face the lampholders Place
wing nut back onto post over the reflector;
then tighten. Lampholder(s) will be aligned
with lamp windows in reflector.

6. Install socket housing unit through plaster

flange opening facing away from the J-Box.
Push reflector into plaster flange until the
reflector is flush against the cieling.

7. Install the proper lamp(s).

IMPORTANT:

FOR WALL WASH UNITS ONLY, FIXTURE MUST BE INSTALLED WITH J-BOX FURTHEST AWAY FROM THE WALL
TO BE ILLUMINATED.

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes.
The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.

Install with J-Box away

from wall to be
illuminated.

J-Box

Advertising
This manual is related to the following products: