Prescolite 4/6SQCFHWW User Manual

Instruction sheet, Installation instructions liteframe, Lf4/6sqcfhww and 4/6sqcfhww

Advertising
background image

Instruction

Sheet

www.prescolite.com

Prescolite

TollFree

Technical

Support

1.888.PRS.4TEC

Hours:

8am

- 5pm

ET

701 Millennium Boulevard • Greenville, SC 29607

With representatives offices in principal cities throughout North America.

Copyright 2012, 1/26/12 revision, All Rights Reserved - Printed in U.S.A.

Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93040115

Instruction

Sheet

INSTALLATION INSTRUCTIONS

LITEFRAME

®

LF4/6SQCFHWW AND 4/6SQCFHWW

1. Install the fixture in the ceiling using hanger bars (supplied), or mounting channel or bar (by others) placed in the adjustable mounting brackets. Mount the

fixture in the ceiling so that the weight of the fixture is supported by the hanger bars, mounting channel, bar, and/or hanger wires secured to the building

structure.

2. Adjust the fixture so the bottom of the plaster flange is flush with the finished ceiling line and in alignment with adjacent fixtures. Secure mounting brackets by

tightening wing nuts on either side of the fixture.

3. Determine where the supply wiring conduit will enter the J-Box and attach it in conformance with the National Electric Code.

4. Remove J-Box cover plate. Remove appropriate knockout and assemble appropriate connector for the supply wire used. Connect ground wires to green ground

leads. Connect white (common) to white (leads). Connect power supply (line) to black lead(s). Reinstall J-Box cover.

WARNING: DO NOT pinch wires between J-Box/ballast cover and J-Box. Consult a qualified electrician for all other options that

require other wiring configurations.

5. Upper reflector (1) can be installed without removing lower reflector and lens. If needed though, the 4 clips (4) can be removed to ease the installation of the

upper reflector (1), the socket box (2) and the wingnut (3).

6. Pull socket box (2) down through opening in fixture. (SEE FIG 1) and remove wingnut (2)

7. Attach socket box to reflector (1) using center hole. Re-install wingnut (3)

8. Install appropriate lamp as needed into socket.

9. Squeeze two torsion springs (5) together and insert ends into two brackets (6). (SEE FIG 1)

10. Push trim assembly up towards ceiling until springs draw trim firmly against ceiling.

NOTE: Orientation of trim should be done so the highest side of reflector (7) is towards the wall.

IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and

instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and

proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and during

servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by

qualified service personnel. Product must be grounded to avoid potential electric shock or other poten-

tial hazard. Product must be mounted in locations and at heights and in a manner consistent with its

intended use, and in compliance with the National Electrical Code and local codes. The use of accessory

equipment not recommended by the manufacturer or installed contrary to instructions may cause an unsafe condition. Do

not block light emanating from product in whole or part, as this may cause an unsafe condition. Do not allow items such

as drapes, curtains, screens or the like to come into contact with the product or to block light from the product, as this may

cause an unsafe condition.

WARNING - This product contains chemicals known to the State of California to cause cancer, birth defects and/or other

reproductive harm. Thoroughly wash hands after installing, handling, cleaning, or otherwise touching this product.

CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-INSTALLED WIRING ON THE FIXTURE. SAFETY AND

PROPER OPERATION OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.

2

3

1

4

5

6

7

Advertising
This manual is related to the following products: