Prescolite LF8MH EB - Manual

Instruction
Sheet
www
.prescolite.com
Prescolite T
ollFree T
echnical Suppor
t
1.888.PRS.4TEC
Hours: 8am - 5pm ET
701 Millennium Blvd, Greenville, SC 29607
With representatives offices in principal cities throughout North America.
Copyright 2008, 07/01/08, All Rights Reserved - Printed in U.S.A.
Part No ....................................................... 93015343
Sheet 1 of 1
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information and instructions
concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials, and proper lamping. Do
not install in areas subject to combustible vapors or gases. Before wiring to power supply and during servicing or relamping, turn
off power at fuse or circuit breaker. All servicing or relamping must be performed by qualified service personnel.
Product must be grounded to avoid potential electric shock or other potential hazard. Product must be
mounted in locations and at heights and in a manner consistent with its intended use, and in compliance
with the National Electrical Code and local building codes. The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from product in
whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or the like to come into
contact with the product or to block light from the product, as this may cause an unsafe condition.
CAUTION: TO REDUCE THE RISK OF ELEC-
TRICAL SHOCK, MAKE CERTAIN THAT THE
POWER SUPPLY IS OFF BEFORE INSTALLING
OR SERVICING THIS FIXTURE.
1. Bend hanger bar brackets as shown (shipped
flat). Install the fixture in the ceiling using B24 or
B6 hanger bars (ordered separately), or mount-
ing channel, bar, or conduit (by others) placed
in the adjustable brackets. Mount the fixture in
the ceiling so that the weight of the fixture is
securely supported by the hanger bars, mounting
channels, bars, conduit, and/or hanger wires
secured to the building stucture.
2. Adjust the fixture so the bottom of the plaster
flange is flush with the finished ceiling line and
in alignment with adjacent fixtures. Secure
mounting brackets by tightening wing nuts on
either side of the fixture.
3. Determine where the supply wiring conduit will
enter the J-Box, remove the appropriate knock-
out, assemble the appropriate connector for the
supply wire used, and attach it in conformance
with the National Electrical Code.
4. Remove J-Box cover plate(s). Connect ground
wires to green ground leads. Connect white
(common) to white (leads). Connect power
supply (line) to black lead(s). Reinstall J-Box
cover. WARNING: DO NOT pinch wires
between J-Box/ballast cover and J-Box.
Consult a qualified electrician for all
other options that require other wiring
configurations.
5. Install reflector (ordered separately) after all ceil-
ing installation and finishing work is complete.
Follow installation instructions provided with
reflector.
6. Install the proper lamp (by others).
Hanger brackets are
supplied flat. Bend the
brackets along the three
oblong holes punched in
the bracket 1/3rd of the
way from each end.
Wing Nut (2)
Socket Cup
Plaster Frame
J-Box Cover (2)
B24 Hanger Bar
(Order Separately)
Reflector
(Order Separately)
INSTALLATION INSTRUCTIONS
LITEFRAME ELECTRONIC BALLAST
METAL HALIDE
LF6MH EB & LF8MH EB
BALLAST REPLACEMENT
MAKE CERTAIN THAT THE POWER SUPPLY IS OFF
Note wire connections and remove wire connectors. Loosen the two hex nuts holding
the ballast to the J-Box. Slide the ballast towards opening in keyhole slots and lift bal-
last off J-Box. Replace ballast by following these steps in reverse order.
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY IN-
STALLED WIRING ON THE FIXTURE. SAFETY AND PROPER OPERATION
OF THE FIXTURE DEPEND ON THE INTEGRITY OF THE WIRING.
THE PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE
CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZ-
ARDS INVOLVED, IN ACCORDANCE WITH THE APPLICABLE INSTALLA-
TION CODE.
KEEP THESE INSTALLATION INSTUCTIONS