Prescolite SDPSCFT - Manual

Instruction
Sheet
www
.prescolite.com
• Prescolite
TollFree
Technical Support
1.888.PRS.4TEC
• Hours: 8am - 5pm ET
101 Corporate Drive • Spartanburg, SC 29303
With representatives offices in principal cities throughout North America.
Copyright 2005, 08/05 revision, All Rights Reserved - Printed in U.S.A.
Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143690100
Instruction
Sheet
INSTALLATION INSTRUCTIONS
SDPSCFT SERIES
J-BOX
1. LOOSEN SCREWS ON J-BOX HALF WAY
(SUPPLIED BY OTHERS).
2a. LOCATE THE BLACK (LINE), WHITE (COMMON),
& GREEN (GROUND) WIRES IN THE J-BOX AND
PASS THESE WIRES THROUGH CENTER HOLE
OF MOUNTING PLATE AS SHOWN IN TOP
FIGURE.
2b. (DIMMING ONLY) THERE WILL BE A GRAY AND
VIOLET WIRE (1 EACH). PASS THESE THROUGH
HOLE WITH OTHER WIRES.
3. ALIGN MOUNTING PLATE TO J-BOX, ROTATE
PLATE COUNTERCLOCKWISE, AND TIGHTEN
WITH SCREWS.
NOTE: THE FIXTURE SHOULD BE ALLOWED TO
HANG ON ITS CHAIN AT THIS POINT.
4a. REMOVE J-BOX COVER PLATE. REMOVE
APPROPRIATE KNOCKOUT AND ASSEMBLE
APPROPRIATE CONNECTOR FOR THE SUPPLY
WIRE USED. CONNECT GROUND WIRES TO
GREEN GROUND LEADS. CONNECT WHITE
(COMMON) TO WHITE (LEADS). CONNECT
POWER SUPPLY (LINE) TO BLACK LEAD(S).
REINSTALL J-BOX COVER.
WARNING: DO NOT PINCH WIRES BETWEEN
J-BOX/BALLAST COVER AND J-BOX. CONSULT
A QUALIFIED ELECTRICIAN FOR ALL OTHER
OPTIONS THAT REQUIRE OTHER WIRING
CONFIGURATIONS.
4b. (DIMMINING ONLY) CONNECT GRAY AND VIO-
LET WIRES (SEE STEP #2b). DIMMING WIRE
CONNECTION MUST NOT BE MADE WITHIN THE
J-BOX TO RETAIN CLASS 2 RATING FOR THE
DIMMING WIRES. MAKE THIS CONNECTION
ONLY AFTER PERFORMING STEP #2b.
IMPORTANT:
DIMMING FIXTURES: 0-10 VOLT CONTROL ONLY.
CAUTION: DO NOT ATTEMPT TO MODIFY OR REWIRE FACTORY-
INSTALLED WIRING ON THE FIXTURE. SAFETY AND
PROPER OPERATION OF THE FIXTURE DEPEND ON
THE INTEGRITY OF THE WIRING.
COVER
BLACK TO
BLACK
WHITE TO
WHITE
MTG. BRACKET
GREEN
J-BOX GREEN
MOUNTING
BRACKET
WHITE
GREEN
BLACK
MOUNTING
PLATE
CHAIN
GREEN BRACKET
GROUND WIRE
WIRE NUT(3)
(NOT SUPPLIED)
STEP #6
IMPORTANT SAFETY INFORMATION. READ AND FOLLOW ALL SAFETY INSTRUCTIONS. Follow label information
and instructions concerning Wet or Damp Locations, installation near combustible materials, insulation, building materials,
and proper lamping. Do not install in areas subject to combustible vapors or gases. Before wiring to power supply and
during servicing or relamping, turn off power at fuse or circuit breaker. All servicing or relamping must be performed by
qualified service personnel. Product must be grounded to avoid potential electric shock or other potential hazard.
Product must be mounted in locations and at heights and in a manner consistent with its intended use, and in
compliance with the National Electrical Code and local codes. The use of accessory equipment not recommended by
the manufacturer or installed contrary to instructions may cause an unsafe condition. Do not block light emanating from
product in whole or part, as this may cause an unsafe condition. Do not allow items such as drapes, curtains, screens or
the like to come into contact with the product or to block light from the product, as this may cause an unsafe condition.