Beltronics 995 - Manual (Page 8)

Programming
12
There are 7 user-selectable options so you
can customize your V995 for your own
preferences. The buttons labeled CITY and
BRT are also used to enter the Program
Mode, REVIEW your current program
settings, and to CHANGE any settings as
desired. The words PGM, RVW, and CHG
are located on the top of the detector, and
are highlighted in colored graphics. Pages
14-16 explain each option in more detail.
How to use Programming
1 To enter Program Mode, press and
hold both the CITY and BRT buttons
down for 2 seconds. (The unit will beep
twice, and will display the word
Program).
2 Then press the RVW button to
review the current settings. (You can
either tap the button to change from item to
item, or hold the button to scroll through
the items).
3 Press the CHG button to change
any setting. (You can either tap the button
to change from setting to setting, or hold
the button to scroll through all the options).
4 To leave the Program Mode, simply
wait 8 seconds without pressing any
button, or press the PWR button. (The
unit will display
Complete, beep 4 times,
and return to normal operation).
An example
Here is how you would turn V995’s
AutoMute feature off.
1 Enter the Program Mode by holding
both the CITY and BRT buttons down for
2 seconds. V995 will beep twice and
display
Program.
2 Then hold the RVW button down.
V995 will scroll through the categories,
starting with Pilot (
Pilot), Voice
( Voice), Power-on sequence (PwrOn),
Signal strength meter ( Meter), and then
AutoMute ( aMute).
3 Release the RVW button when V995
shows the AutoMute item. Since the factory
setting is for AutoMute to be on, V995 will
display
aMute ON.
(If you accidentally don’t release the
RVW button in time, and V995 goes to the
next category, hold the RVW button down
again, and after V995 scrolls through all
categories, it will begin again at the top of
the list.)
4 Press the CHG button to change from
aMute ON to aMute OFF.
5 To complete the Programming, simply
wait 8 seconds without pressing any button,
or press the PWR button. The V995 will
display
Complete, beep 4 times, and return
to normal operation.
Overview of Programming
13
Pilot HWY
Pilot H
Pilot V
Voice ON
Voice OFF
PwrOn STD
PwrOn FST
Meter STD
Meter TEC
aMute ON
aMute OFF
City STD
City LoX
City NoX
Bands ALL
Bands MOD
X ON or OFF (default is on)
K ON or OFF (default is on)
Ka ON or OFF (default is on)
POP ON or OFF (default is off)
Ku ON or OFF (default is off)
LSR ON or OFF (default is on)
SWS ON or OFF (default is off)
Press the CHANGE button
to change your setting
within a category
* Full word: Highway or AutoScan or City
Letter: H or A or C
Vehicle voltage
* Voice alerts on
Voice alerts off
* Standard power-on sequence
Fast power-on sequence
* Standard signal strength meter
Tech Display
* AutoMute on
AutoMute off
* Standard City mode sensitivity
Low X band sensitivity in City Mode
No X band sensitivity in City Mode
* All bands enabled
One or more bands are disabled
Turn bands “ON” or “OFF” by
pressing the VOLUME/MUTE button
Press the REVIEW button
to go from one category
to the next
PILOT
(Power-on indication)
VOICE
POWER-ON SEQUENCE
SIGNAL STRENGTH METER
AUTOMUTE
CITY MODE SENSITIVITY
BANDS
* Factory Default Settings
To reset V995 to its original factory
settings, press and hold the “CITY”
and “BRT” buttons while turning
the power on. V995’s display will
provide a “Reset” message,
accompanied by an audible alert,
acknowledging the reset.